Eaton Crouse-Hinds Z130 Instruction Manual

Also see for Crouse-hinds series: Operating instructions Instruction manual Operating instructions Operating instructions Instruction manual

Contents

Eaton Crouse-Hinds Z130 Instruction Manual Manual pdf 19 page image

INM MTL 130-0200 Rev 415Table 1 - Common groups (continued)Send Function Reply (verbose) Reply (terse) Limits (where applicable) NotesAxPy Parameters.P9 Terse=0 P9=1 0 or 1 1 to set instrument into tersemode – 0 to set verboseP8 A2 Mode=1 P8 =1 0 to 3 0, 1, 2, 3 in terse - Off, High,Low, status in verboseP7 A2 Hyst=1.0% P7 =1.0 1 to 10 (1dp) Alarm hysteresisP6 A2 Level=5.0% P6 =5.0 0 to 100 Alarm trip pointP5 A1 Mode=1 P5 =1 As alarm 2 As alarm 2P4 A1 Hyst=1.0% P4 =1.0 As alarm 2 As alarm 2P3 A1 Level=5.0% P3 =5.0 As alarm 2 As alarm 2P2 4mA=0% P2 =0 Will show 0V or 4mAdepending on variant.P1 20mA=50% P1 =50 0 to 100 Zero and FSD limits areinteractive.AxRy Reading* see (8) belowR5 Comp2=N/A R5 =0R4 Temp=Normal R4 =1 Heater state – see also heatererrors.R3 Alarm2=Normal R3 =0 0 to 2 Alarm state – Off, Normal,ALARM or N/A (if not fitted)R2 Alarm1=Normal R2 =0 0 to 2 In terse mode alarm state is1 in alarm and 0 for all otherstatesR1 Conc=5.00% R1 =5.00 Instrument range and resolution Measure and ConcentrationNotes on readings:- In over-range condition (110% of instrument span) xxxxx will be ‘+++++’ (e.g. ‘R1 Conc= +++++’). Similarly in under-rangecondition (-5% of instrument span) xxxxx will be ‘-----’. In the case of a system error R1 will be replaced by the error code e.g. ? 72 In verbosemode a brief fault description will be appended. ‘Conc’ & ‘%’ are determined by sensor type and unit – see ‘U’ below. Resolution is applica-tion dependant. Where a fault is present in the secondary reading it will be indicated by a text description in verbose mode and by a code inthe case of Zr units (heater does not return a numeric value in R4) or by -999 or +999 to indicate downscale or upscale failures respectively.AxUy Unit(read only)U13 Test Flags=0 U13=0U12 Factory Flags=0 U12=0U11 Output=mA* U11=1 Analogue output: 0=4/20mA,1= 0/1V, 2 = 0/5V, 3=0/20mAU10 Sens 2 Ch=1 U10=1 Sens 2 ADC chan (9)U9 R2 unit=mV U9=2U8 R2 type=T/C U8 =14U7 R1 Ch=1 U7 =1U6 R1 unit=% U6 =1U5 R1 type=Z U5 =13U4 F/w rev=0.24 U4 =0.24U3 F/w p/n=290-6031 U3 =290-6031U2 S/n = I-700123 U2=I-700123U1 Addr=0 U1 =0 Sensor Card Address