Eaton ELC-GP02 Instruction Sheet

Also see for ELC-GP02: Catalog

IL05003005E.pdfELC-GP02GRAPHIC PANEL SERIESInstruction SheetWARNING• DANGER - DC input power must be disconnected before any maintenance. Do not connect ordisconnect wires and connectors while power is applied to the circuit. Maintenance must beperformed by qualified technicians.• DANGER - The ELC-GP02 requires 24VDC input power. The 24VDC input power should not beconnected to the RS-485 communication port. The unit may be destroyed or can’t be repaired ifthe input power is improperly applied. Please always check the correctly input power wiringbefore apply power.• DANGER - An electrical charge will remain on the DC-link capacitors for 1 minute after powerhas been removed. Do not conduct any wiring or investigation on the ELC-GP02 until 1 minuteafter power has been removed. Do NOT touch terminals when power on.• CAUTION - Always ground the ELC-GP02 by using the grounding terminal. Not only this acts asa safety, but also filter out electrical noise. The ground method must comply with the laws of thecountry where the unit is to be installed.• CAUTION - ELC-GP02 may be damaged if the fixed support (shipped with the pack) is adjustedtoo tight.• Please carefully read this instruction before using the ELC-GP02.• The ELC-GP02 display panel is waterproof. But please prevent grease, corrosive liquids andsharp objects from contacting the ELC-GP02.• Do not disconnect while circuit is live unless area is known to be non-hazardous.• This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D or Non-HazardousLocations only.• Explosion Hazard – Substitution of components may impair suitability for class I, Division 2.• Explosion Hazard – Do not disconnect equipment unless power has been switched off or thearea is known to be Non – Hazardous.• Power, input and output (I/O) wiring must all be in accordance with Class I, Division 2 wiringmethods, Article 501-4 (b) of the National Electrical Code, NEPA 70,or as specified in Section18-152 of the Canadian Electrical Code for units installed within Canada, and in accordancewith that location’s authority.1 INTRODUCTION1.1 Model ExplanationThank you for choosing Eaton Logic Controler (ELC) GP series products. The features of ELC-GP02are: resolution is 160*32, display 10*2 Chinese characters max. and Multilanguage support. Built-intwo communication ports (RS-232 and RS-485/RS-422, can be used simultaneously).Communication and alarm indication LEDs. Extension slot for ELC-GPXFERMOD to copy settingsand programs rapidly and save download time. Built-in variety objects to meet your requirements.1.2 Outline1.3 Panel Function ExplanationPANEL COMPONENT EXPLANATIONAlarm Indication LEDStatus 1: When power is on, the LED will flash three times slowly.Status 2: When there is an abnormal situation, the LED will flash quickly along with analarm sound.RS-232 Indication LED(Yellow) It will be flashing when transmitting program and communicating by using RS-232.RS-485 Indication LED(Green) It will be flashing when communicating by using RS-485.LCM display Area Liquid Crystal Module display area used to display current program state.Esc Escape/Exit) Used to cancel an incorrect input, or to Exit a programming step.Arrow KeysUP/Pg Up: Used to increase the value or move up one page.Pg Dn/DOWN: Used to decrease the value or move down one page.Left: Left direction key. (move curser to left)Right: Right direction key. (move cursor to right)Enter Key Used to input a value or accept a programming command.Function KeysF0/0: It is used to be constant 0 and user can define the function of F0.F1/1: It is used to be constant 1 and user can define the function of F1.F2/2: It is used to be constant 2 and user can define the function of F2.F3/3: It is used to be constant 3 and user can define the function of F3.F4/4: It is used to be constant 4 and user can define the function of F4.F5/5: It is used to be constant 5 and user can define the function of F5.F6/6: It is used to be constant 6 and user can define the function of F6.F7/7: It is used to be constant 7 and user can define the function of F7.F8/8: It is used to be constant 8 and user can define the function of F8.F9/9: It is used to be constant 9 and user can define the function of F9.1.4 Back Panel5-PIN terminals:Wire gauge: 12-24 AWGTorque: 4.5 lb.-inch1.5 DimensionFront panel (unit: mm [inch]) Right side diagram (unit: mm [inch])Vertical view (Unit: mm)1.6 InstallationMounting ELC-GP02 into the opening is done by carefully fitting the unit into the opening andpressing firmly on all four corners. You could fix it by using the fixed support packaged withELC-GP02. You should infix the fixed support in the back cover and turn the screw in to fix.Warning: If you turn the screw exceeds torque: 4-5(kg-cm), ELC-GP02 may be damaged.(Note：the flat surface shoud be a Type 4 “Indoor Use Only” enclosure or equivalent.)Please leave sufficient space (more than 50mm) around the unit for heat dissipation.Thickness:0.5~9.0mm50mm50mmMounting dimension (unit: mm [inch])Thickness Range 0.5~9mm135~136.5[5.31~5.37]85[3.35]2 ELECTRICAL SPECIFICATION2.1 Electrical SpecificationITEM ELC-GP02Function Key / Digital Key F0/0~F9/9, ESC, ENTER and ARROW keysExternal Input Power 24VDC (-15%~20%) 3W MAX.Memory Capacity 256K ByteCPU Hitachi MAX002RAM of System 32K ByteCommunication Interface COM1: RS-232 and COM2: RS-485Waterproof Class of Front Panel IP65/NEMA4/UL Type 4 (indoor use)Environment Condition 0~50℃, relative humidity 20-90% RH（non-condensing）Storage Temperature of Hardware -20~60 °CVibration 5Hz≦f＜9Hz = Continuous: 1.75mm / Occasional: 3.5mm9Hz≦f≦150Hz = Continuous: 0.5g / Occasional: 1.0gImpact 15g peak, 11ms duration, half-sine, three shocks in each direction peraxis, on 3 mutually perpendicular axes (total of 18 shocks)RF Radiation Test CISPR11, Class AStatic Electricity Discharge Test EN61000-4-2RF Radiation Test EN61000-4-3High Frequency Transient Test EN61000-4-4Weight / Dimension 0.24kg / 147×97×35.5mm (Weight(W)×Height(H)×Deep(D))Cooling Method Natural Air-CoolingTemperature Code T6Hazardous Location rating Class I, Division 2, Group A, B, C, and D2.2 Function SpecificationITEM ELC-GP02Display Screen Screen STN-LCDColor MonochromaticBack-lightThe back-light automatic turn off time is 1~99 minutes(0 = do not to turn off)(back-light life is about 50 thousand hours at 25℃)Resolution 160X32 dots

/ 2

Related manuals for Eaton ELC-GP02