Eaton EWFFSC15 Quick Start Manual
Set-up the DeviceAdd your device to the Brightlayer Home AppSTEP 1 : Double click on the “ON” button on theWi-Fi Smart Fan Speed Control (EWFFSC15).Status LED on the Wi-Fi Smart Fan Speed Controlshould be blinking cyan to indicate that the deviceis in set-up mode. If the status LED is not blinking,refer to the Troubleshooting guide.STEP 2 : Log in to your account on the BrightlayerHome AppSTEP 3 : Select “Devices” optionOnce initial device is installed, additional devicescan be added using the global add (+) button.Once selected the devices would be displayed asshown below:Note: Now the user can utilize many features that areavailable such as creating schedules, scenes, presetlight levels and minimum/maximum brightness settingsthrough the Brightlayer Home App.Next click on “Add a Device” option shown in thescreen belowSelect the device type to addFCC STATEMENTThis device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions:1: This device may not cause harmful interference, and2: This device must accept any interference received, including interference thatmay cause undesired operation.NOTE: This equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FCC Rules. These limits are designedto provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radio frequency energyand, if not installed and used in accordance with the instructions, may cause harmfulinterference to radio communications. However, there is no guarantee that interfer-ence will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning theequipment off and on, the user is encouraged to try to correct the interference byone or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.• Consult the dealer or an experienced radio/TV technician for help.FCC CAUTION: Any changes or modifications not expressly approved by EatonWiring Devices could void the user’s authority to operate the equipment.This device complies with Industry Canada’s license-exempt RSSs. Operation issubject to the following two conditions:(1) This device may not cause interference; and(2) This device must accept any interference, including interference that may causeundesired operation of the device.EATON WIRING DEVICES LIMITED 2 YEAR WARRANTYEaton Wiring Devices warrants its Fan Speed Control to be free of defects inmaterials and workmanship in normal use and service for a period of two years fromdate of original purchase. THIS TWO (2) YEAR LIMITED WARRANTY IS IN LIEU OFALL OTHER WARRANTIES, OBLIGATIONS, OR LIABILITIES, EXPRESSED OR IMPLIED(INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR APARTICULAR PURPOSE THAT IS IN DURATION IN EXCESS OF TWO YEARS FROMTHE DATE OF ORIGINAL CONSUMER PURCHASE). NO AGENT, REPRESENTATIVE, OREMPLOYEE OF EATON HAS AUTHORITY TO INCREASE OR ALTER THE OBLIGATIONSOF EATON UNDER THIS WARRANTY. To obtain warranty service for any properlyinstalled Eaton Fan Speed Control that proves defective in normal use send the de-fective Fan Speed Control prepaid and insured to Quality Control Dept., Eaton WiringDevices, 203 Cooper Circle, Peachtree City, GA 30269; in Canada: Eaton Wiring Devic-es, 5925 McLaughlin Road, Mississauga, Ontario L5R 1B8. Eaton will repair or replacethe defective unit, at its option. Eaton will not be responsible under this warranty ifexamination shows that the defective condition of the unit was caused by misuse,abuse, improper installation, alteration, improper maintenance or repair of damage inshipment to Eaton. EATON SHALL HAVE NO RESPONSIBILITY FOR INSTALLATION OFTHE Fan Speed Control, OR FOR ANY PERSONAL INJURY, PROPERTY DAMAGE, ORANY SPECIAL, INCIDENTAL, CONTINGENT, OR CONSEQUENTIAL DAMAGES OF ANYKIND, RESULTING FROM DEFECTS IN THE Fan Speed Control OR FOR BREACH OFANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. THE EXCLUSIVE REME-DY FOR BREACH OF THE LIMITED WARRANTY CONTAINED HEREIN IS THE REPAIROR REPLACEMENT OF THE DEFECTIVE PRODUCT AT EATON’S OPTION. IMPLIEDWARRANTIES (IF ANY) INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIESOF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY, ARE LIMITEDIN DURATION TO A PERIOD ENDING TWO YEARS FROM THE DATE OF ORIGINALCONSUMER PURCHASE. IN NO CASE SHALL EATON’S LIABILITY UNDER ANYOTHER REMEDY PRESCRIBED BY LAW EXCEED THE PURCHASE PRICE. Some statesdo not allow the exclusion or limitation of incidental or consequential damages orallow disclaimers or modifications of or limitations on how long an implied warrantylasts, so the above limitations may not apply to you. Some Canadian provinces do notallow exclusion or variance of implied warranties so that some or all of the abovelimitations may not apply to you. This warranty gives you specific legal rights and youmay also have other rights which vary from state to state and province to province.Read enclosed instructions carefully. If you have any questions concerning use orcare of this product, please write: Consumer Service Division, Eaton Wiring Devices,203 Cooper Circle, Peachtree City, GA 30269.Troubleshooting guide Wi-Fi Smart Fan Speed Control colorchange kit installation instructionsHow to download the AppSTEP 1 :Pull out the air gapswitch at the top ofthe device and thensqueeze the top tabson both sides of thedeviceSTEP 2 :Pull faceplate offSTEP 3 :Line up all tabs andsnap the faceplateon and push the airgap switch inNOTE: Not all products include color change kits.Get your Wi-Fi Smart Device running in 3 easy steps!Your installationis finished!Enjoy your newWi-Fi Smart Fan speed control!WarrantyLED statusAvailable in 3 different color change kitsFor troubleshooting contact us at:TechSupport@eaton.com orcall 1-877-386-2273 opt. 5 then opt. 3STEP 3 (continued) :Amazon, Alexa and all related logos are trademarks of Amazon.com,Inc. or its affiliates. Google and Google Play are trademarks of GoogleLLC. Wi-Fi CERTIFIED logo is a trademark of the Wi-Fi Alliance.STEP 3 (continued) :Symptom Possible Cause SolutionDevice doesn’t function.All LEDs are OFF A)B)C)D)Circuit breaker is openor trippedAir Gap switch on thefan speed control ispulled outImproper wiringDefective fan speedcontrolA)B)C)D)Turn ON/Close the circuitbreakerPush in the disconnectswitch on the fan speedcontrolCheck and correct wiringReplace fan speed controlDevice functions normallyusing the fan speed controlpush buttons but not fromBrightlayer Home App. PurpleLED indicator is blinking ONand OFF about once per secondFan speed control is notincluded in the Wi-FinetworkA)B)C)Include the fan speedcontrol in the Wi-Fi networkusing Brightlayer Home AppCheck that the router isfunctioning properlyGo through the factoryreset procedure and re-addthe device to the BrightlayerHome AppDevice functions normallyusing the fan speed controlpush buttons but not fromBrightlayer Home App. YellowLED indicator is blinking ONand OFF about once per secondNo Wi-Fi signal Check the routerDevice functions normally bothlocally and from a BrightlayerHome App but can’t becontrolled from the standard3-way switchThe 3-way wire is notconnected Refer to the wiring connectionand check if the 3-way wire isconnectedFan speed control is warm totouch after a period of time This is normal if the loadis within the fan speedcontrol limitsNo action requiredQuick reference table for Wi-Fi Smart Fan Speed Control(EWFFSC15) functionalityFunction Devicestate Button Numberof secondsto pressLedindicatorcolor DefaultFull speed ON/OFF ON 2 GreenPower up state ON OFF 5 Blue OFFLevel LEDindicator OFFbrightnessOFF OFF 15 White Level 1Level LEDindicator ONbrightnessON ON 15 White Level 3Power LEDindicator ONbrightnessON ON 20 Yellow Level 3Power LEDindicator OFFbrightnessOFF OFF 20 Yellow Level 1Factory reset ON/OFF ON 30 RedFor more information, visitEaton.com/smarthomeDownload the AppSearch and download the Brightlayer Home Appvia the App Store or Google Play.Select “Create an Account” to create an accountby following the instructions on the screen. |
Related manuals for Eaton EWACD
manualsdatabase
Your AI-powered manual search engine