Eaton KME6-1875-2 Installation Instructions Manual

Contents

Form 6 recloser control KME6-1875-1, KME6-1875-2, and KME6-1875-3fiber optic converter kits installation instructions5 InstallatIon InstructIons MN280079EN May 2017CAuTIONEquipment misoperation Do not connect this controlto an energized recloser until all control settings havebeen properly programmed and verified Refer to theprogramming information for this control Failure tocomply can result in control and recloser misoperation,equipment damage, and personal injury G110 39. Verify the RS-232 and RS-485 Communication Ports areset for the intended protocol:●● Modbus●● DNP3 Protocol, Level 2●● 2179The RS-232 and RS-485 data ports can be specifiedwith DNP3, 2179, or Modbus protocol. The protocol isuser-configured to either the RS-232 or RS-485 serialports via the ProViewTM interface software.Refer to the Communications WorkbenchTM section ofService Information S280-70-4 Form 6 Microprocessor-Based Recloser Control Programming Guide foradditional information.CAuTIONEquipment misoperation Do not energize thisequipment until all control settings have been properlyprogrammed and verified Refer to the electronic controlinstallation manual for programming procedures Failureto comply can result in misoperation (unintendedoperation), equipment damage, and personal injury G119 210. Return the Form 6 yard mount recloser controlto service.Refer to Service Information MN280076EN Form 6Microprocessor-Based Yard Mount Recloser ControlInstallation and Operation Instructions for the procedureReturn the Control to Service.TB1123 5 7 9 11 13 15 17 194 6 8 10 12 14 16 18CI1 CI2 CI3 SS1 CO1 CO2 CO3 CO4CI4CI1 CI2 CI3 SS1 CO1 CO2 CO3 CO4TB3 1 3 5 7 9 11 13 15 17 19 21CI5 CI6 CI7 CI8 CI9 CI10 CI11 CO5 CO6TB42 4 6 8 10 12 14 16 18 20CI4 CI5 CI6 CI7 CI8 CI9 CI10 CI11 CO5 CO61 3 5 7 9 11 13CO7 CO8 CO9 CO10 CO11 CO122 4 6 8 10 12CO7 CO8 CO9 CO10 CO11 CO12J1 -RS-232 J2 -IRIG-BTTL IRIG-BJ3 -RS-4852-Wire RS-485RECLOSER INTERFACE CONNECTIONSA1D3F5 72B4C6ETB6RS-232 DTETB2 •1 2•3 4•5 6•7 8•9 10•11 12•13 14•15 16•17 18•19 20I(1-2) I(3-4) I (5-6) V(1-2) V(3-4) V(5-6) V1I(SEF)FUSE(10 AMP)FUSE(10 AMP)TB5+1-52- 4+INPUT POWER AUXILIARY POWER28 VDC#10 Terminal of WireAssembly Lead onMounting Stud9-Pin Cable Connectedto RS-232 PortFiber Optic Power CableConnected to Terminal Block TB5Black Wire Connected to TB5-5Red Wire Connected to TB5-4Fiber Optic ConverterAssemblyMode Switch Set tothe OFF PositionDTE/DCE Switch Setto the DCE PositionFigure 4 KME6-1875-2 fiber optic converter installed in the Form 6 yard mount recloser control cabinet

/ 12

Related manuals for Eaton KME6-1875-1