Eaton Power Xpert 9395 Installation And Operation Manual

Also see for Power Xpert 9395: Installation and operation manual Installation and operation manual Installation and operation manual Installation and operation manual Installation and operation manual

Contents

UPS OPERATING INSTRUCTIONSPower Xpert 9395 UPS (300 kVA) Installation and Operation Manual 164201728 Rev 2 www.eaton.com/powerquality7-67.2.6 Display Menu OperationTable 7‐3 describes the menu functions and and how to use them.Table 7‐3. Display Menu OperationFunction Subfunction OperationEvents Press the EVENTS pushbutton on the main menu bar or History menu bar to display a listing ofall system events that are currently active. The most recent event is listed first. As events clear,they are removed from the Active System Events listing. To scroll through the events, press theup or down arrow pushbutton on the menu bar.User History Press the HISTORY pushbutton on the Active Events menu bar to display the User History Log.The User History Log lists up to 500 system events in chronological order, with the most recentevent listed last (once 500 is reached, the earliest event is overwritten). The end of the log (themost recent events) is displayed first; scroll upward to view older event listings. To scrollthrough the events, press the up or down arrow pushbutton on the menu bar. To return to theActive Events screen, press the EVENTS pushbutton on the menu bar.Service History The Service History Log is for service personnel and is password protected. If the customerneeds access to the log, contact an Eaton service representative.Press the SERVICE pushbutton on the User History menu bar to display the Service History Log.The Service History Log lists up to 500 service events in chronological order, with the mostrecent event listed last (once 500 is reached, the earliest event is overwritten). The end of the log(the most recent events) is displayed first; scroll upward to view older event listings. To scrollthrough the events, press the up or down arrow pushbutton on the menu bar. To return to theUser History screen, press the USER pushbutton on the menu bar. To return to the Active Eventsscreen, press the EVENTS pushbutton on the menu bar.Meters The Meter screens show the UPS meter readings for the unit. The default voltage displayed onthese screens is phase-to-neutral. However, an authorized Eaton Customer Service Engineercan change the screens to display the voltage phase-to-phase (A-B, B-C, C-A). Press theMETERS pushbutton on the main menu bar to display the Unit Meter screens. To scroll throughthe meter screens, press the up or down arrow pushbutton on the menu bar. The current UPSreadings are displayed in the information area of the screen.Output The Output screen shows output voltage (phase‐to‐neutral), output current (each phase), andfrequency being supplied by the UPS, as well as the kVA, kW, and power factor measurements.Input The Input screen shows input voltage (phase‐to‐neutral), input current (each phase), andfrequency of the incoming utility source, as well as the kVA, kW, and power factormeasurements.Bypass The Bypass screen shows the bypass input voltage (phase‐to‐neutral), input current (eachphase), and frequency of the incoming utility source, as well as the kVA, kW, and power factormeasurements.Battery The Battery screen displays the battery voltage (Vdc), the battery current (Idc), the minutes ofbattery time remaining, and battery temperature. Battery temperature must be set up by anauthorized Eaton Customer Service Engineer. When battery life decreases to less than 20%,Check Battery is displayed.Statistics The Statistics screen displays the hours on line and the total kW hours used.Output Current The Output Current screen displays a real‐time bar graph of the output current of the UPS. Thegraph shows the current for each phase.Output Power The Output Power screen displays the power in kW and kVA for each UPM.System Level 0 Setup Function Selection This screen can be used to set the screen contrast, show the firmware versions installed,identify the unit type and enter a password to access Level 1 functions. Press the SETUPpushbutton on the main menu bar to display the System Setup Level 0 Screen. No password isnecessary to access Level 0 functions. Use the up or down arrow pushbutton to highlight thesetup function screen desired, then press the SELECT pushbutton to display the function screen.