FAAC 615 Instruction Manual

Also see for 615: User guide Instructions Instructions Manual

Contents

FAAC 615 Instruction Manual Manual pdf 4 page image

2ENGLISHCE DECLARATION OF CONFORMITY FOR MACHINES(DIRECTIVE 98/37/EC)Manufacturer: FAAC S.p.A.Address: Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALYDeclares that: Barrier mod. 615BPR,• is built to be integrated into a machine or to be assembled with other machinery to create a machine underthe provisions of Directive 98/37/EC;• conforms to the essential safety requirements of the other following EEC directives:2006/95/EC Low Voltage Directive2004/108/EEC Electromagnetic Compatibility DirectiveFurthermore, the manufacturer declares that the machinery must not be put into service until the machine intowhich it will be integrated or of which it will become a component has been identified and its conformity to theconditions of Directive 89/392/EEC and subsequent modifications assimilated in Italian National legislation underPresidential Decree No. 459 of 24 July 1996 has been declared...Bologna, 1 st September 2009The Managing DirectorA. MarcellanWARNINGS FOR THE INSTALLERGENERAL SAFETY OBLIGATIONS1) ATTENTION! To ensure the safety of people, it is important that you readall the following instructions. Incorrect installation or incorrect use ofthe product could cause serious harm to people.2) Carefully read the instructions before beginning to install the product.3) Do not leave packing materials (plastic, polystyrene, etc.) within reachof children as such materials are potential sources of danger.4) Store these instructions for future reference.5) This product was designed and built strictly for the use indicated in thisdocumentation. Any other use, not expressly indicated here, couldcompromise the good condition/operation of the product and/or bea source of danger.6) FAAC declines all liability caused by improper use or use other than thatfor which the automated system was intended.7) Do not install the equipment in an explosive atmosphere: the presenceof inflammable gas or fumes is a serious danger to safety.8) The mechanical parts must conform to the provisions of Standards EN12604 and EN 12605.For non-EU countries, to obtain an adequate level of safety, the Stand-ards mentioned above must be observed, in addition to national legalregulations.9) FAAC is not responsible for failure to observe Good Technique in theconstruction of the closing elements to be motorised, or for any defor-mation that may occur during use.10) The installation must conform to Standards EN 12453 and EN 12445.For non-EU countries, to obtain an adequate level of safety, the Stand-ards mentioned above must be observed, in addition to national legalregulations.11) Before attempting any job on the system, cut out electrical power.12) The mains power supply of the automated system must be fitted with anall-pole switch with contact opening distance of 3 mm or greater. Useof a 6A thermal breaker with all-pole circuit break is recommended.13) Make sure that a differential switch with threshold of 0.03 A is fittedupstream of the system.14) Make sure that the earthing system is perfectly constructed and con-nect metal parts of the closure to it.15) The automated system is supplied with an intrinsic anti-crushing safetydevice consisting of a torque control. Nevertheless, its tripping thresh-old must be checked as specified in the Standards indicated at point10.16) The safety devices (EN 12978 standard) protect any danger areasagainst mechanical movement Risks, such as crushing, dragging, andshearing.17) Use of at least one indicator-light (e.g. FAACLIGHT ) is recommendedfor every system, as well as a warning sign adequately secured to theframe structure, in addition to the devices mentioned at point “16”.18) FAAC declines all liability as concerns safety and efficient operation ofthe automated system, if system components not produced by FAACare used.19) For maintenance, strictly use original parts by FAAC.20) Do not in any way modify the components of the automated sys-tem.21) The installer shall supply all information concerning manual operationof the system in case of an emergency and shall hand over to the userthe warnings handbook supplied with the product.22) Do not allow children or adults to stay near the product while it isoperating.23) Keep remote controls or other pulse generators away from children,to prevent the automated system from being activated involuntarily.24) Transit is permitted only when the automated system is idle.25) The user must not attempt any kind of repair or direct action whateverand contact qualified personnel only.26) Check at least every 6 months the efficiency of the system, particularlythe efficiency of the safety devices (including, where foreseen, theoperator thrust force) and of the release devices.27) Anything not expressly specified in these instructions is not permit-ted.