Fein AFMT12SL Manual
Also see for AFMT12: Instruction manualOriginal instructionsInstruction manual
                  | |
18 enDo not reach into the area of the clamping jaws.Otherwise there is danger of crushes or contusionsto the fingers.Do not operate the power tool with with open clamp-ing jaws and without an application tool! This coulddamage the power tool.When the clamping jaws are open before the appli-cation tool is inserted, pivot the clamping levertoward the front and then back again. The clampingjaws are closed now. The application tool can beinserted.Handling the battery.Operate and charge the battery only within the batteryoperating-temperature range of 0°C – 45°C (32°F –113°F). At the beginning of the charging procedure, thebattery temperature must be within the battery operat-ing-temperature range.The real percentage of the battery charge condition isonly indicated when the power tool motor is stopped.The electronics automatically switch off the motor priorto the battery being deep discharged.Notes on sanding.Press the power tool with the sanding sheet briefly andfirmly against a flat surface and briefly switch the powertool on. This provides for good adhesion and preventspremature wear.When only one tip or corner of the sanding sheet isworn, it can be removed again and reattached turned by120°.Work with the entire surface of the sanding plate, notonly with the edge or tip.When sanding with small triangle sanding plates, select ahigh oscillating frequency (electronics level 4 – 6); whensanding with the round sanding plate and the large trian-gle sanding plate, select a moderate oscillating frequency(max. electronics level 4).Sand with continuous motion applying moderate pres-sure. Applying excessive pressure does not increase therate of removal, it only wears off the sanding sheet faster.Notes on sawing.Select a high oscillating frequency. Round saw blades canbe released and clamped offset again, to allow for uni-form wearing off.Notes on scraping.Select a moderate to high oscillating frequency.Repair and customer service.When working metal under extreme operat-ing conditions, it is possible for conductivedust to settle in the interior of the power tool.Blow out the interior of the power tool via the ventila-tion slots frequently with dry and oil-free compressed air.For storage of the power tool, remove the applicationtool, shut the clamping lever, and then press in the fasten-ing element.The current spare parts list for this power tool can befound in the Internet at www.fein.com.AFMT12(SL): For storage of the power tool, remove theapplication tool and screw the clamping bolt in to thestop.If required, you can change the following parts yourself:Clamping bolt (AFMT12(SL)), application toolsWarranty and liability.The warranty for the product is valid in accordance withthe legal regulations in the country where it is marketed.In addition, FEIN also provides a guarantee in accordancewith the FEIN manufacturer’s warranty declaration.The delivery scope of your power tool may include onlya part of the accessories described or shown in thisInstruction Manual.Declaration of conformity.FEIN declares itself solely responsible for this productconforming with the relevant provisions given on the lastpage of this Instruction Manual.Technical documents at: C. & E. Fein GmbH, C-DB_IA,D-73529 Schwäbisch GmündEnvironmental protection, disposal.Packaging, worn out power tools and accessories shouldbe sorted for environmental-friendly recycling.Dispose of batteries only when discharged.For batteries that are not completely discharged, insulatethe terminals with tape as a protective measure againstshort-circuiting.LED indica-torMeaning Activity1 – 4 greenLEDPercentage ofcharge condi-tionOperationContinu-ous redlightBattery isalmost emptyCharge batteryRed flash-ing lightBattery is notready foroperationBring the battery intothe battery operating-temperature range, thenchargeOBJ_BUCH-0000000247-001.book Page 18 Thursday, January 28, 2016 2:33 PM |
Related manuals for Fein AFMT12
manualsdatabase
Your AI-powered manual search engine