Fein RS10-70E Instruction Manual

Contents

declaration of conformity

14 enFor your safety.Read all safety warnings and allinstructions. Failure to follow thewarnings and instructions may result in electric shock,fire and/or serious injury.Save all warnings and instructions for future reference.Do not use this power tool before you have thor-oughly read and completely understood thisInstruction Manual and the enclosed “GeneralSafety Instructions” (document number3 41 30 054 06 1). The documents mentioned should bekept for later use and enclosed with the power tool,should it be passed on or sold.Please also observe the relevant national industrial safetyregulations.Intended use of the power tool:Hand-guided sander for dry belt sanding of surfaces ofmetal, plastic, wood, composite materials, paint/varnish,filler and similar materials in weather-protected environ-ments with the application tools and accessories recom-mended by FEIN.This power tool is also suitable for use with AC genera-tors with sufficient power output that correspond to theStandard ISO 8528, design type G2. This Standard is par-ticularly not complied with when the so-called distortionfactor exceeds 10 %. When in doubt, please refer to thegenerator instruction/specification guide.Special safety instructions.Wear personal protective equipment. Depending on appli-cation, use face shield, safety goggles or safety glasses.Where appropriate, wear dust mask, hearing protectors,gloves and workshop apron capable of stopping smallabrasive or workpiece fragments. The eye protectionmust be capable of stopping flying debris generated byvarious operations. The dust mask or respirator must becapable of filtrating particles generated by your opera-tion. Prolonged exposure to high intensity noise maycause hearing loss.Hold power tool by insulated gripping surfaces, becausethe belt may contact its own cord. Cutting a “live” wiremay make exposed metal parts of the power tool “live”and could give the operator an electric shock.While working, do not wear loose clothing, jewellery oropen, long hair. Despite protective devices, loose objectscan be snagged or caught by moving parts and lead toinjury.Do not use worn, torn or heavily clogged sanding belts.Handle sanding belts carefully and store them accordingto the manufacturer’s instructions. Do not bend or foldsanding belts! Damaged sanding belts can tear, be flungaway and injure someone.Never touch the running sanding belt and do not reachunder the protective guard. Danger of injury.Secure the work piece firmly. A work piece that isgripped tightly in a clamping device or vice, is moresecure than if held by hand.Hold the power tool firmly. High reaction torque canbriefly occur.Do not rivet or screw any name-plates or signs onto thepower tool. If the insulation is damaged, protectionagainst an electric shock will be ineffective. Adhesivelabels are recommended.Do not use accessories which are not specificallydesigned and recommended by the power tool manufac-turer. Safe operation is not ensured merely because anaccessory fits your power tool.Clean the ventilation openings on the power tool at regu-lar intervals using non-metal tools. The blower of themotor draws dust into the housing. An excessive accu-mulation of metallic dust can cause an electrical hazard.Before putting into operation, check the mains connec-tion and the mains plug for damage.Recommendation: The tool should always be suppliedwith power via a residual current device (RCD) with arated current of 30 mA or less.Handling hazardous dustsFor work procedures with this power tool where mate-rial is removed, dusts develop that can be hazardous toone’s health.Contact with or inhaling some dust types, e. g. asbestosand asbestos-containing materials, lead-containing coat-ings, metal, some wood types, minerals, silicate particlesfrom materials containing stone, paint solvents, woodpreservatives, antifouling paints for vessels, can triggerallergic reactions to the operator or bystanders and/orlead to respiratory infections, cancer, birth defects orother reproductive harm. The risk from inhaling dustsdepends on the exposition. Use dust extraction matchedappropriately for the developing dust, as well as personalprotective equipment and provide for good ventilation ofthe workplace. Leave the processing of asbestos-contain-ing materials to specialists.Wood and light-metal dust, hot mixtures of sanding dustand chemical materials can self-ignite under unfavourableconditions or cause an explosion. Avoid sparking in thedirection of the dust collector as well as overheating ofthe power tool and the materials being sanded, empty thedust collector/container in time, observe the materialmanufacturer’s working instructions, as well as the rele-vant regulations in your country for the materials beingworked.m, s, kg, A, mm, V,W, Hz, N, °C, dB,min, m/s 2m, s, kg, A, mm, V,W, Hz, N, °C, dB,min, m/s 2Basic and derived units of measurement from theinternational system of units SI.Character Unit of measure-ment, internationalUnit of measure-ment, nationalExplanationWARNINGOBJ_BUCH-0000000019-002.book Page 14 Monday, December 17, 2012 4:12 PM