GE 6100 Series Data Manual

3geappliances.comElectric Heat Amps include electric heater and fan motor current draw.265-volt units are to be permanently connected in compliance with National Electrical Code and local codes and have a factory-installed junction box on the chassis.Each 265-volt sub-base kit consists of sub-base with appropriate receptacle for minimum circuit amperage, chaseway to route power connector from sub-base to chassisand wiring to connect sub-base to building wiring.265-Volt Power Connection Kit must be ordered separately.Power Connection KitsZoneline® Chassis NomenclatureThe Zoneline chassis is identified by a model number defining the type of unit, cooling capacity, electrical information andoptional features included on the unit. When specifying or ordering the Zoneline chassis, the use of this nomenclature willassure receiving the correct unit.230/208-Volt Line Cord Connection UnitsLine CordKitElectricHeatBTUHElectricHeaterWattsElectricHeatAmpsMin. CircuitProtection(Amps)RAK3153A 8150/7900 2400/2320 11.0/11.6 15RAK3203A 11200/10900 3300/3200 15.1/16.0 20RAK3303A 16000/15450 4700/4530 21.2/22.4 30Electric Heat Amps include electric heater and fan motor current draw.Each Line Cord Kit has an integral Leakage Current Detection and Interruption (LCDI) or Arc FaultCurrent Interrupter (AFCI) device as required by National Electrical Code (NEC) and UnderwritersLaboratories (UL) for units manufactured after August 1, 2004.230/208-Volt Sub-Base and Direct Connected UnitsSub-BaseDirectConnectionKitElectricHeatBTUHElectricHeaterWattsElectricHeatAmpsMin. CircuitProtection(Amps)RAK204D15P RAK4157 8150/7900 2400/2320 11.0/11.6 15RAK204D20P RAK4207 11200/10900 3300/3200 15.1/16.0 20RAK204D30P RAK4307 16000/15450 4700/4530 21.2/22.4 30Electric Heat Amps include electric heater and fan motor current draw.Units connected through sub-base do not require an LCDI or AFCI device since they are notconsidered to be line-cord connected. Each 230/208-volt sub-base kit consists of sub-base withappropriate receptacle for minimum circuit amperage, chaseway to route power connector fromsub-base to chassis, wiring to connect sub-base to building wiring and a short line cord with 9-pinconnector to connect to chassis and plug into receptacle in sub-base.Short sub-base line cord may not be used without sub-base.Junction box for 230/208-volt chassis must be purchased separately.RAK4002A for 2900, 3900, 4100, and 6100 series units, RAK4002B for 5800 series units.265-Volt Sub-Base and Direct Connected UnitsSub-Base PowerConnection KitDirectConnection KitElectric HeatBTUHElectric HeaterWattsElectric HeatAmpsMin. Circuit Protection(Amps)RAK204E15 RAK5172 RAK5157 8150 2400 9.6 15RAK204E20 RAK5202 RAK5207 11550 3400 13.3 20RAK204E30 RAK5302 RAK5307 16350 4800 18.6 30ImportantEssential Elements Ordering Overview230/208-volt line cord connected units — order line cord kit230/208-volt sub-base connected units — order sub-base265-volt units — order sub-base and power connection kitEXAMPLEA Z 6 1 H 1 2 D A DChassis series41=deluxe line cool/electric heat61=deluxe line heat pumpUnit typeE=cooling with electricresistance heatH=heat pump with electricresistance heatZonelinepackagedterminalchassisNominal cooling capacity07=7,000 BTUH cooling09=9,000 BTUH cooling12=12,000 BTUH cooling15=15,000 BTUH cooling Special FeaturesB=base unitC=corrosion treatedD=internalcondensateremoval (ICR)system (heatpump modelsonly) (not forcoastal areas)P=Dry Air 25 (4100Series only)Voltage/Phase/FrequencyD=230/208-Volt,single-phase, 60 HzE=265-Volt, single-phase,60 HzUniversalpower connection