GE JV535 Owner's Manual And Installation Instructions

Also see for JV535: Owner's manual and installation instructions Owner's Manual & Installation Instructions Owner's Manual & Installation Instructions Owner's manual and installation instructions Owner's manual and installation instructions

Contents

13MARK HOLESSelect the vent option that your installation willrequire and proceed to that section:Hood mounting screws (4)1315⁄16″ (30″ hood)1615⁄16″ (36″ hood) 1315⁄ 16″ (30″ hood)1615⁄ 16″ (36″ hood)Cabinet frontCenterlineElectrical access hole(in cabinet bottom)Wood shims (recessed-bottom cabinets only)Vertical ductaccess hole101⁄ 2″11⁄2″2″71⁄2″5″ 11⁄4″A. Outside top exhaust(Vertical duct–3 1⁄ 4″ x 10″ Rectangular)• Use the diagram or the hood as a template andmark the locations on the cabinet for ductwork,electrical wiring and keyhole screw slots.B. Outside top exhaust (Vertical duct–7″ Round)• Use the diagram or the hood as a template andmark the locations on the cabinet for ductwork,electrical wiring and keyhole screw slots.Hood mounting screws (4)1315⁄16″ (30″ hood)1615⁄16″ (36″ hood)1315⁄16″ (30″ hood)1615⁄16″ (36″ hood)Cabinet frontCenterlineElectrical accesshole (in cabinet bottom)Wood shims (recessed-bottom cabinets only)Accesshole for 7″round duct101⁄2″11⁄2″2″71⁄2″5″Cabinetbottom 8″ DIA.HOLECUT HOLESCut holes at marked locations for duct and electricalwiring. For the vertical duct, cut out 3/4″ extratoward the front of the cabinet so you can move theduct freely when installing the hood. It may also easeinstallation by cutting the hole 101⁄2″ instead of 10″.FOR RECESSED-BOTTOMCABINETS ONLYRUN WIRESRun the electrical wires through the wall orcabinet according to National Electrical Codeand applicable local codes.NOTE: DO NOT turn the power on untilinstallation is complete.Cabinet Bottom11131214Installation InstructionsSCREW IN PARTWAYDrive a mounting screw (from the hardware packet)partway into each center of the narrow neck of thekeyhole slots marked on the cabinet bottom.FEED IN WIRESLift the hood into position and feed the housewiring through the wiring knockout.1516Wood shims (recessed-bottom cabinets only)Cabinet frontCenter line Electrical access hole(in wall)Hood mounting screws (4)Horizontal ductaccess holeCabinetbottom1315⁄16″ (30″ hood)1615⁄16″ (36″ hood)3⁄4″1⁄8″33⁄4″51⁄4″ 51⁄4″71⁄2″1315⁄16″ (30″ hood)1615⁄16″ (36″ hood)C. Outside rear exhaust(Horizontal duct–31⁄4″ x 10″ Rectangular)• Use the diagram or the hood as a template andmark the locations on the cabinet for ductwork,electrical wiring and keyhole screw slots.D. Recirculating (non-vented ductless–Available on JV5 Series models only)• Use the hood as a template and mark the locationson the cabinet for the electrical wiring and keyholescrew slots.• Since the hood is to be recirculated (not to be ventedoutside), do not cut out any vent openings in thewall or cabinet bottom.Wood shims• If the cabinets have front, side or back trim, make2 wood shims the width of the trim and attachthem to the cabinet bottom recess on both sides.See Step 11 for marking locations.51⁄4″51⁄ 4″

/ 16

Related manuals for GE JV535