GE MiCOM P40 Agile Technical Manual

Also see for MiCOM P40 Agile: Technical manual Technical manual Technical manual Technical manual Technical manual

PRP/HSR/RSTP/FailoverFrom S1 Agile 2.0.1. onwards cards that support the PRP/HSR/RSTP/Failover protocols in any of the combinationsare configured using the Redundant Ethernet Configurator software tool. If you are using a ZN008700X card onlythis tool supports it. If using S1 Agile 1.4.2 or older you will need to use the PRP/HSR Configurator for PRP and/orHSR, and the RSTP Configurator for RSTP cards.SHP or DHPIf using SHP or DHP the first two octets are set by the Switch Manager software or an SNMP MIB browser. The thirdoctet is fixed at 254 (FE hex, 11111110 binary), and the fourth octet is set by the on-board dip switch.Note:An H35 (SHP) or H36 (DHP) network device is needed in the network to configure the REB IP address if you are using SNMP.Board Part No. Compatible WithRedundant Ethernet SHP, 2 multi-mode fibre ports + modulated IRIG-B ZN0071 001 Switch ManagerRedundant Ethernet SHP, 2 multi-mode fibre ports + demodulated IRIG-B ZN0071 002 Switch ManagerRedundant Ethernet RSTP, 2 multi-mode fibre ports + modulated IRIG-B ZN0071 005Redundant Ethernet Configurator(S1 Agile 2.0.1 onwards) / RSTPConfigurator (S1 Agile 1.4.2 orolder)Redundant Ethernet RSTP, 2 multi-mode fibre ports + demodulated IRIG-B ZN0071 006Redundant Ethernet Configurator(S1 Agile 2.0.1 onwards) / RSTPConfigurator (S1 Agile 1.4.2 orolder)Redundant Ethernet DHP, 2 multi-mode fibre ports + modulated IRIG-B ZN0071 007 Switch ManagerRedundant Ethernet DHP, 2 multi-mode fibre ports + demodulated IRIG-B ZN0071 008 Switch ManagerRedundant Ethernet PRP, 2 multi-mode fibre ports + modulated IRIG-B ZN0071 009Redundant Ethernet Configurator(S1 Agile 2.0.1 onwards) / PRP/HSRConfigurator (S1 Agile 1.4.2 orolder)Redundant Ethernet PRP, 2 multi-mode fibre ports + demodulated IRIG-B ZN0071 010Redundant Ethernet Configurator(S1 Agile 2.0.1 onwards) / PRP/HSRConfigurator (S1 Agile 1.4.2 orolder)Redundant Ethernet PRP/HSR, 2 multi-mode fibre ports + modulated IRIG-B ZN0071 109Redundant Ethernet Configurator(S1 Agile 2.0.1 onwards) / PRP/HSRConfigurator (S1 Agile 1.4.2 orolderRedundant Ethernet PRP/HSR, 2 multi-mode fibre ports + demodulated IRIG-B ZN0071 110Redundant Ethernet Configurator(S1 Agile 2.0.1 onwards) / PRP/HSRConfigurator (S1 Agile 1.4.2 orolder)Redundant Ethernet PRP/HSR/RSTP/Failover, 2 multi-mode fibre ports +Modulated/Un-Modulated IRIG-B ZN0087 001 Redundant Ethernet Configurator(S1 Agile 2.0.1 onwards)Chapter 4 - ConfigurationPx4x-REB-TM-EN-6 33