GE Profile PT925DN Dimensions And Installation Information

Also see for Profile PT925DN: Installation instructions Owner's manual

Contents

installation instructions

Listed byUnderwritersLaboratoriesFor answers to your Monogram,® GE Profile™ orGE® appliance questions, visit our website atge.com or call GE Answer Center ® service,800.626.2000.Specification Revised 4/09220244PT925DNGE Profile™ 30" Built-In Single/Double Convection Wall OvenKW Rating240V 3.9208V 2.9Breaker Size240V 20 Amps208V 20 AmpsDimensions and Installation Information (in inches)Most 30” Wall Cabinets can be used with this unit.Note: These ovens are not approved forstackable installations. Cabinets installedadjacent to wall ovens must have an adhesionspec of at least a 194°F temperature rating.Door handle protrudes 3" from door face. Cabinetsand drawers on adjacent 45° and 90° walls shouldbe placed to avoid interference with the handle.Electric wall ovens are not approved forinstallation with a plug and receptacle. Theymust be hard wired in accordance withinstallation instructions.Installation Information: Before installing, consultinstallation instructions packed with product forcurrent dimensional data.Side-by-side installations require at least 2"between cutouts.CUTOUTHEIGHT27 1/4" MIN.27 5/16" MAX.CUTOUTWIDTH28 1/2" MIN.28 5/8" MAX.5"22" TOBOTTOM OFJUNCTION BOXJUNCTION BLOCATIONRECOMMENDEDCUTOUTLOCATION32 1/2"FROM THEFLOORCABINETWIDTH30"ALLOW 11/16" FOROVERLAP OF THEOVEN OVER SIDEEDGES OF CUTOUTTHE OPENINGBETWEEN INSIDEWALLS MUSTBE AT LEAST28 1/2"WIDEALLOW 1" FOROVERLAPON OVEN TOPAND BOTTOMOF CUTOUT21"ALLOW A MINIMUMF 21" FOR CLEARANCEADJACENT CORNERS,RAWERS, WALLS ETC.N THE DOOR IS OPENED.Allow 11/16”(1.75 cm) foroverlap of ovenover side edgesof cutoutCutoutWidth28 1/2”(72.4 cm)Min.28 5/8”(72.7 cm)Max.15”(38.1 cm)CabinetWidth30”(76.2 cm)Allow a minimumof 15” (38.1 cm) forclearance to adjacentcorners, drawers,walls, etc. whendoor is openAllow 1” (2.5 cm)minimum foroverlap of oventop and 1 1/4”(3.2 cm) overlapof oven bottomof cutoutRecommendedcutoutlocation fromfloor 26 1/2”(67.3 cm) maxOpeningBetweenInside WallsMust BeAt Least28 1/2”(72.4 cm)WideJunction BoxLocation(junction boxmay belocated inadjacentcabinet)9 1/2”(12.7 cm)Max.CutoutHeight27 1/4”(69.2 cm) Min.27 5/16”(69.4 cm) Max.22” (55.9 cm)Min. toBottom ofJunction BoxCL 2 x 4 orequivalentrunnersSuitablebracingto supportrunners21-5/8"over centerlineof cabinet(must support 275 lbs.)Cutout width28-1/2'' MIN.28-5/8'' MAX.30Recommendedcutout location32-1/2"from floor21Junctionboxlocatione, or etc.p and bottom edges of cutout.f oven over side edges of cutout.with trim.Conduit(72"long)527-1/4'' MIN.27-5/16'' MAX.Cutout heightAB23-1/2'' MIN.Cutout depth22'' MIN.

/ 3

Related manuals for GE Profile PT925DN