Garland XG24-JIB Installation And Operation Manual

Also see for XG24-JIB: Service manual

Part # 4523133 Rev 4 (08/04/09) Page 17If ignition of the burner does not occur on the first trial, thebottom indicator light will flash amber. If the burner(s) donot light within four trials for ignition, the control will displaya flashing warning, “IGNITION ERROR.” The flashing amberlight will turn to solid red and an audible alarm will sound. Ifthis occurs, turn the main power switch off, wait 5 minutes,and then repeat steps 2 and 3.To Cook in Two-Sided Mode:1. To start a cook cycle select a product recipe by using theproduct keys (1 through 9) or by using the UP/DOWNkeys or to select a product recipe.The display alternately blinks the recipe and the wordSELECTED 2 times then the recipe displays continuously.2. The controller regulates the platen and grill temperaturesto the set temperatures of the product selected andreads “TOO COOL” or “TOO HOT” with “MENU ITEM”, untilthe grill attains the set temperature range for the item.NOTE: If the display reads either “TOO COOL” or “TOO HOT”the upper platen will not lower and initiate a cookingsequence.3 After loading the product onto the grill, press the greenCANCEL/RAISE PLATEN BUTTON and BLACK buttonsimultaneously. A cook cycle starts and the upper platenlowers if the product selected is clamshell recipe.4 To cancel a cook cycle at anytime press the greenCANCEL/RAISE PLATEN BUTTON and the upper platenwill rise if the product recipe selected is clamshell recipe.5. During a cook cycle, the display shows the product recipename in the first line and the remaining cook time countdown in the second line.6 When the cook timer reaches one, (1), second remaininga pre-time-out alarm sounds alerting the operator.7 When the cooking time has been completed the platenraises automatically. On the controller the “PRODUCTNAME” and the word “REMOVE” will be displayed and anaudible alert will sound.8. Pressing the green CANCEL/RAISE PLATEN BUTTON stopsthe audible alert and the unit will revert back to IDLEmode.To Cook in Flat Grill Mode:1. To start a cook cycle select a product recipe by using theproduct keys (1 through 9) or by using the UP/DOWNkeys or to select a product recipe.OPERATION continuedThe display alternately blinks the recipe and the wordSELECTED 2 times then the recipe will be displayedcontinuously.2. The controller regulates the grill temperature to the settemperature of the product selected and reads “TOOCOOL” or “TOO HOT” with “MENU ITEM”, until the grillattains the set temperature range for the item.NOTE: If the display reads either “TOO COOL” or “TOO HOT” itwill not initiate a cooking sequence.3 After loading the product onto the grill, press the greenCANCEL/RAISE PLATEN BUTTON and BLACK buttonsimultaneously. That will start a cook cycle if the productselected is clamshell recipe.4 To cancel a cook cycle at anytime the press the greenCANCEL/RAISE PLATEN BUTTON .5. During a cook cycle, the display shows the product recipename in the first line and the remaining cook time countdown in the second line.6. The display shows the “SEAR” or “FLIP” alarm messagewith flashing in the second line if the current cookingproduct is flat recipe and the sear time or flip time is notzero.7. A cook alarm sounds with a repeating beep pattern.Pressing the black RAISE button acknowledges the “SEAR”or “FLIP” alarm message if the alarm field in system setupis set to MANUAL.8. The “SEAR” or “FLIP” alarm message stops after 5 secondsif the alarm field in system setup is set to AUTO.9. When a cook is complete, the display shows the productrecipe name in the first line and a flashing “REMOVE”message in the second line. A repeating beeping alarmalso sounds.10. Pressing the black RAISE button cancels the cook donealarm.11. The unit revertes back to IDLE mode.Enter Standby Mode:Stand by mode is used during slow periods to conserveenergy with out a complete shut down of the unit. Whencooking temperatures are again required, pre-heat cooktemperature/time is reduced. Stand by mode temperaturescan be adjusted, see the PROGRAMING section.1. Select Standby Mode by pressing or until“STANDBY” is displayed.