Contents - Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- INTRODUCTION
- Organization
- Definitions/Abbreviations
- Units of Measure
- Section 1 1-1 –
- SYSTEM DESCRIPTION
- Figure 2-2, Transponder
- Figure 2-3 GSU-75 ADAHRS with Connector and Mounting Tray
- Figure 2-4, GDL 69A SXM Datalink
- G1000 Optional Interfaces
- G1000 Normal Mode
- Section 2 2-1 –
- SOFTWARE AND CONFIGURATION
- Figure 3-1, SET>ACTV Diagram
- Figure 3-2, Loss of Communication
- G1000 System Software Information
- Figure 3-5, GSU Configuration Settings Storage
- Configuration Mode
- Figure 3-6, Garmin Unit S/N Location
- G1000 Software/Configuration Procedure
- System Software and Configuration Load
- Figure 3-8 – Airframe Group Selection
- Figure 3-9 – Airframe Change Confirmation
- Feature Enablement
- Aircraft Registration Number Entry
- Configuration Manager
- Splash Screen Loading
- Figure 3-10, MFD Aux - Database Page DB Transfer
- Configuration of Navigation Map for Traffic System
- Interface Confirmation
- Section 3 3-1 –
- Servicing Information
- Maintenance Intervals
- Electrical Bonding Test
- GSU 75 Earth Magnetic Field Updates
- Section 4 4-1–
- TROUBLESHOOTING
- System Annunciations
- G1000 Alerting System
- Synthetic Vision and Pathways Troubleshooting
- Backup Communications Path Checks
- GDU 105X Troubleshooting
- GDU 105X Alerts
- GTX Troubleshooting
- GDL69A SXM Troubleshooting (if installed)
- GSU 75 and GMU 44 Troubleshooting
- Figure 5-5, Magnetometer Interference Test
- Table 5-3, Magnetometer Interference Test Sequence
- GSU 75 Troubleshooting
- Software/Configuration Troubleshooting
- Backshell/Backplate Connectors
- Section 5 5-1 –
- EQUIPMENT REMOVAL & INSTALLATION
- GDU 1054B/1050
- GDL 69A SXM (if installed)
- Figure 6-1, Configuration Module Installation
- Figure 6-2, GSU 75 Configuration Module Installation
- Section 6 6-1 –
- GARMIN G1000 LRU REPLACEMENT/CONFIGURATION & TESTING
- Figure 7-1, G1000 Normal Mode Check
- GMA 1347 Audio Panel
- GIA 63W Integrated Avionics Unit
- Figure 7-2, Aux – GPS Status Page (MFD)
- GEA 71 Engine/Airframe Unit
- Figure 7-3, Normal Engine Instrument Markings (MFD)
- GTX 335R, GTX 345R, or GTX 33 Transponder
- Figure 7-4, Aircraft Registration
- GSU 75 ADAHRS (if installed)
- GDC 74A Air Data
- Table 7-1, Altitude Test Points
- Table 7-2, Airspeed Test Points
- GRS 77 and GMU 44 Magnetometer (if installed)
- GMU 44 Magnetometer
- GSU/GRS/GMU Calibration Procedures
- Table 7-4, Required GRS/GMU Calibrations
- Figure 7-5, GRS/GMU Calibration, Pitch/Roll Offset
- Figure 7-6, GRS/GMU Calibration, Engine Run-Up
- Figure 7-7, Normal Mode AHRS Check
- GDL 69A or GDL 69A SXM Data Link (if installed)
- GSA 81 Servos (if installed)
- Garmin Traffic Systems (GTS 800) (if installed)
- Section 7 7-1–
- SUBSYSTEM FUNCTIONAL CHECKS
- ChartView Functional Check
- SafeTaxi Functional Check
- DME Functional Check
- Section 8 8-1 –
- G1000 SYSTEM RETURN TO SERVICE PROCEDURE
- Figure 9-2, PFD Power-up System Annunciations
- Figure 9-3, PFD Normal Operation
- Display Failure Test
- Reversion Mode Check
- GPS Signal Acquisition
- GPS Failure Test
- GIA Failure Test
- GEA Functional Check
- G1000 Backup Path Test
- Appendix A
| 
G1000 Supplemental Maintenance Manual Page 3-20Textron Nav III Series Revision 3190-02128-04GSU 75 Software/Configuration Loading (if installed)Follow this procedure to configure the GSU 75 ADAHRS. Do not follow the procedures in thissection if a GSU 75 is not installed in the aircraft.Move the cursor to the Item window and rotate FMS inner knob to display drop downmenu. Highlight “Baseline Option – GSU75 Installation” and press the ENT key toselect it.Press the CHK All softkey.In the PRODUCT window, move the cyan selection box down with the large FMS knobto highlight the “CARD COPY” configuration check box. Press the ENT key to uncheckthe configuration check box.Press the Load softkey.Monitor the loading progress and verify the software load completes without errors asindicated by the following:• Green “PASS” or White “N/A” in all Configuration and Software columns.• “Upload Complete………….COMPLETE” in the summary box.Press the ENT key to acknowledge the prompt that appears in the pop-up box.GTX 335 Transponder Software/Configuration Loading (if installed)Follow this procedure to configure the GTX 335 transponder in the aircraft. Do not follow theprocedures in this section if a GTX 335 is not installed in the aircraft.Move the cursor to the Item window and rotate FMS inner knob to display drop downmenu. Highlight “Baseline Option – GTX 335 Installation” and press the ENT key toselect it.Press the CHK All softkey.In the PRODUCT window, move the cyan selection box down with the large FMS knobto highlight the “CARD COPY” configuration check box. Press the ENT key to uncheckthe configuration check box.Press the Load softkey.Monitor the loading progress and verify the software load completes without errors asindicated by the following:• Green “PASS” in the Configuration and Software columns for each item loaded.• “Upload Complete………….COMPLETE” in the summary box.Press the ENT key to acknowledge the prompt that appears in the pop-up box. |
