Garmin striker 4 Owner's Manual
Also see for striker 4: Quick start guideUser manualInstallation instructions
number to display water depth. Enter a 0 in this value todisplay depth below keel and depth below transducer.2 Select Settings > My Vessel > Keel Offset.3 Select or based on the location of the transducer.4 Enter the distance measured in step 1.Setting the Water Temperature OffsetYou can set the temperature offset to compensate for thetemperature reading from a temperature-capable sensor.1 Measure the water temperature using the temperature-capable transducer that is connected to the device.2 Measure the water temperature using a differentthermometer or temperature sensor that is known to beaccurate.3 Subtract the water temperature measured in step 1 from thewater temperature measured in step 2.This is the temperature offset. Enter this value in step 5 as apositive number if the sensor connected to the devicemeasures the water temperature as being colder than itactually is. Enter this value in step 5 as a negative number ifthe sensor connected to the device measures the watertemperature as being warmer than it actually is.4 Select Settings > My Vessel > Temp. Offset.5 Use the arrow keys to enter water temperature offsetmeasured in step 3.Alarms SettingsNavigation AlarmsSelect Settings > Alarms > Navigation.Arrival: Sets an alarm to sound when you are within a specifieddistance or time from a turn or a destination.Anchor Drag: Sets an alarm to sound when you exceed aspecified drift distance while anchored.Off Course: Sets an alarm to sound when you are off course bya specified distance.System AlarmsAlarm Clock: Sets an alarm clock.Device Voltage: Sets an alarm to sound when the batteryreaches a specified low voltage.GPS Accuracy: Sets an alarm to sound when the GPS locationaccuracy falls outside the user-defined value.Sonar AlarmsSelect Settings > Alarms > Sonar.Shallow Water: Sounds when the water depth is shallower thanthe specified depth.Deep Water: Sounds when the water depth is deeper than thespecified depth.Water Temp.: Sounds when the water temperature varies morethan ± 2°F (± 1.1°C). Alarm settings are saved when thedevice is turned off.NOTE: You must connect the device to a temperature-capable transducer to use this alarm.Fish: Sets an alarm to sound when the device detects asuspended target.• sets the alarm to sound when fish of all sizes aredetected.• sets the alarm to sound only when medium or largefish are detected.• sets the alarm to sound only when large fish aredetected.Unit SettingsSelect Settings > Units.System Units: Sets the unit format for the device.Variance: Sets the magnetic declination, the angle betweenmagnetic north and true north, for your present location.North Reference: Sets the direction references used incalculating heading information. True sets geographic northas the north reference. Grid sets grid north as the northreference (000º). Magnetic sets the magnetic north as thenorth reference.Position Format: Sets the position format in which a givenlocation reading appears. Do not change this setting unlessyou are using a map or chart that specifies a differentposition format.Map Datum: Sets the coordinate system on which the map isstructured. Do not change this setting unless you are using amap or chart that specifies a different map datum.Time Format: Sets a 12-hour, 24-hour, or UTC time format.Time Zone: Sets the time zone.Daylight Savings Time: Sets daylight savings time to Off or On.Navigation SettingsNOTE: Some settings and options require additional hardware.Select Settings > Navigation.Route Labels: Sets the type of labels shown with route turns onthe map.Turn Transition Activ.: Sets the turn transition to be calculatedbased on time or distance.Turn Transition Time: Sets how many minutes before the turnthat you transition to it as the next leg, when Time is selectedfor the Turn Transition Activ. setting.Turn Transition Dist.: Sets how far before the turn that youtransition to it as the next leg, when Distance is selected forthe Turn Transition Activ. setting.Route Start: Selects a starting point for route navigation. Youcan select Boat to start navigation from the current vessellocation, or Waypoints to start from the first waypoint on theroute.Restoring the Factory Default SettingsNOTE: This deletes all settings information you have entered.1 Select > System > System Information > FactorySettings.2 Select an option.8 Device Configuration |
Related manuals for Garmin striker 4
Garmin STRIKER Vivid 4 Owner's Manual
Garmin STRIKER VIVID Owner's Manual
Garmin striker 4 User Manual
Garmin STRIKER VIVID 5cv Owner's Manual
Garmin STRIKER VIVID 7sv Owner's Manual
Garmin 400C Owner's Manual
Garmin 150 Owner's Manual
Garmin 350C Owner's Manual
Garmin STRIKER 4 Quick Start Manual
Garmin CS 1522 Owner's Manual
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine