Gemini CDJ-02 Operation Manual

Contents

Gemini CDJ-02 Operation Manual Manual pdf 5 page image

(5)(5)(5)(5)(5)PITCH BEND BUTTONS: Pushing the PITCH BEND BUTTONS (20)will automatically raise the pitch up to +4% or lower the pitch down to-4% from the existing pitch setting. Releasing the buttons will return thepitch to the original pitch setting. You can use this function to match thepitch bend when mixing from one song to another.PITCH CONTROL SLIDE: Moving the PITCH CONTROL SLIDE (21)up or down will lower or raise the pitch percentage.JOG WHEEL: Use the JOG WHEEL (22) to make fine adjustments inpause mode for cueing or bending the pitch for precise synchronizationin play mode.PGM (PROGRAM): Use the PGM (23) section for DIRECT SELECT orto create a TRACK PROGRAM. Please refer to the PGM section fordetailed instructions.OPERATING INSTRUCTIONS:1. Place a CD in the DISC IN SLOT (6).2. Push the TRACK SKIP (12) buttons to select the track you want to play.3. Press the PLAY/PAUSE (9) button and the unit will instantly play.CUE INSTRUCTIONS:1. To start the play at a point other than the beginning of a track, followthese instructions:First select the track you wish to play, and then press PLAY/PAUSE (9)so the unit goes into the play mode. Press PLAY/PAUSE (9) to pauseplay at the spot where you want the play to start the CUE POINT. Usethe SEARCH BUTTONS (13) or JOG WHEEL (22) to pick the precisespot you want play to begin, then press PLAY/PAUSE (9) again to savethe cue point. Press the CUE (8) button to pause play at the cue point (theunit will go into the pause mode and the location indicated on the displaywill be the memorized cue point). You can preview the cue point bypressing and holding down CUE (8). Press PLAY/PAUSE (9) to beginplay from the cue point.2. Once you have saved a cue point you can fine tune or change thememorized cue point:To change a cue point, push PLAY/PAUSE (9) so the unit plays from thecue point, then press PLAY/PAUSE (9) at the spot you wish your newcue point to be. Press PLAY/PAUSE (9) again to save the cue point. Theunit will go into the pause mode and the location indicated on the displaywill be the new memorized cue point.To fine tune a cue point, pause play at the memorized cue point, thenuse the SEARCH (13) buttons or JOG WHEEL (22) to scan frame byframe (1/75th of a second) to where you want play to begin. PressPLAY/PAUSE (9) to save the new cue point.NOTE: DURING FINE TUNING THERE WILL BE A STUTTER EFFECT (TO HELP YOU FIND THEBEAT). THE STUTTERING EFFECT WILL END WHEN YOU PRESS PLAY/PAUSE (9) TO SAVETHE CUE POINT. ALSO, DURING FINE TUNING IF YOU HOLD DOWN THE SEARCH (13)BUTTON, THE UNIT WILL SCAN QUICKLY.PGM:PROGRAM:First press STOP/EJECT (7) once followed by PGM to enter PROGRAMmode. Select a TRACK NUMBER with the NUMBER PAD and press SETafterwards to set a track for that slot. Continue to select tracks andpress the SET button, until satisfied with a program of tracks. Thenpress PLAY/PAUSE (9) to start the program. To exit a PROGRAMpress the STOP/EJECT (7) button twice or hold the button down toEJECT the CD. SINGLE-AUTO CUE modes will function normallywith PROGRAM mode.DIRECT SELECT:To DIRECTLY SELECT a TRACK, simply press the TRACK NUMBERyou want to hear. If you select TRACK NUMBERS 1-9 you may use0 before the number for, example 01 for track number 1. For tracks 11and higher use the first digit then followed by second digit to jump to thattrack. SINGLE-AUTO CUE modes will function normally withDIRECT SELECT mode.NOTE: PROGRAM AND DIRECT SELECT MODES WORK INDEPENDTLY, TO USE EITHER MODETHE DISC MUST BE EJECTED AND REINSERTED.TROUBLESHOOTING:• If the disk will not play, check to see if the disc was loaded correctly(label side up). Also check the disc for excessive dirt, scratches, etc.• If the disc turns but there is no sound, check the cable connections. Ifthey are okay, check your amplifier or receiver.• If the CD skips, check the CD for dirt or scratches. Do not assume thatthe CD player is defective. Many CDs are recorded out of spec and willskip on most or all CD players. Before sending the unit in for repair, tryplaying a CD that you are sure plays properly.SPECIFICATIONS:GENERAL:Disc Type................................Standard Compact discs (12 cm & 8 cm)Time Display.....................Track Elapsed, Track Remain, or Total remainVariable Pitch......................................± 16% Slider with Resume SwitchStart...........................................................................Within 0.03 secondsTrack Selection.....................................................................1 to 99 TracksAUDIO SECTION:Quantization......................................1 Bit Linear/Channel, 3 Beam LaserOversampling Rate..........................................................................8 TimesSampling Frequency.....................................................................44.1 kHzFrequency Response......................................................20 Hz to 20 kHzTotal Harmonic Distortion..............................................Less Than 0.005%Signal to Noise Ratio.....................................................................>96 dBDynamic Range.................................................................................>94 dBOutput Level (nominal)........................................................1.9 Volts R.M.S.Power Supply.......................................................AC 120/230V, 60/50 HzDimensions...............................12.5” x 8.3” x 3.75” (31.5 x 21 x 9.5mm)Weight...................................................................................5.65 lbs. (2.56 kg)SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGEWITHOUT NOTICE FOR PURPOSE OF IMPROVEMENT.