Gemini GEM-P9600 User Manual

Also see for GEM-P9600: Applications Installation instructions Installation instructions Programming instructions Programming instructions

Gemini GEM-P9600 User Manual Manual pdf 26 page image

X GEM-P9600 Installation Instructions L NAPCO Security SystemsWI742D 5/03! Page 26ALARM INDICATION!If programmed to silence an alarm, enter a valid User Code and press the U button.The keypad must have permission to disarm the alarm (Alarm, Pulse Alarm, Fire Output, Reset Output or Auxiliary Out-puts) from the specific area. This can be done through the PC Quickloader software, Area Features Screen or Area Bell Con-trol.Should a burglary alarm occur, the red ARMED LED will flash, and the display will alternately read "ALARM", then the zonesviolated. Disarm the panel; the display will read "ALARM" and will continue to indicate the violated zones until the C buttonis pressed or the panel is armed once again.FUNCTION MODE/DEALER PROGRAM MODEThe keypad can provide a wide assortment of utility functions as summarized in the Keypad Function Mode. The functionsare displayed in a prompting "YES/NO" format. To skip a function, answer NO (press the PRIOR/NO button); to select and exe-cute a function, answer YES (press the P button or the U button). The complete function list is provided here in its normaldisplayed sequence. However, since not all functions are designed for all systems (or intended for all users), only functionsthat are applicable and active are displayed. (For example, if no zones are bypassed, "DISPLAY ZN BYPASSED" will not appear).Furthermore, functions that are intended for use by the installer or servicer will not be displayed. Note: Functions may bemanually scrolled forward or backward using the R and the B buttons, respectively.To return to normal keypad operation, press the C button. (The keypad will automatically return to its normal operat-ing mode if no activity is detected for longer than one minute). Note: Due to space constraints, GEM-RP2ASe2/GEM-K2ASmessage displays are abbreviated.Remember: (1) Functions that are not active, not programmed and/or not applicable to the user's authority level will besuppressed and will not display. (2) Press the PRIOR/NO button to skip a function; press the NEXT/YES button to execute it.(3) The GEM-RP2ASe2/GEM-K2AS displays abbreviated messages that autoscroll.DISPLAY ZN FAULTSPress the YES button to identify all unsecured zones (within the keypad's area) while disarmed. Press NEXT button toscroll through the zones. (Zones may be bypassed in this mode by pressing the B button). Manually bypassed zones willbe indicated when displaying status.DISPLAY ZN BYPASSEDPress YES button to display zones that have been deactivated. Press NEXT button to scroll through the zones.DISPLAY ZN DIRECTORYPress YES button to display a list of all programmed zone descriptions in the keypad area. Press NEXT button to scrollthrough the zones. To return to the system, press the C button at any time.ACTIVATE BELL TESTPress YES button to activate the burg relay output (while disarmed) for about 2 seconds. If the device does not sound, itmay be defective.DISPLAY PHONE #'SThe panel can function as an auto dialer to any of four programmed telephone numbers. (Telephone numbers must beprogrammed through Napco PCD-Windows Quickloader software). Select Telephone #1-4 using NEXT and PRIOR buttons,then press the U button. Pick up the phone to initiate dialing of the displayed number. (The phone will appear to be discon-nected while dialing but will return to normal after a few seconds).DISPLAY SYS TRBLPress YES button to check trouble (LOW BATTERY, AC POWER LOSS, etc.). Wait for the display to scroll through multi-ple system troubles, or use the NEXT and PRIOR buttons to manually scroll.DISPLAY FIRE ALARMTo display Fire Zone(s) in alarm, access DISPLAY FIRE ALARM and scroll through the zones using the NEXT button.Correct the problem, then press the C button to restore the "SYSTEM READY" condition.DISPLAY FIRE TRBLTo display Fire Zone(s) in trouble, access DISPLAY FIRE TRBL and scroll through the zones using the NEXT button. Cor-rect the problem, then press the C button to restore the "SYSTEM READY" condition.BASIC OPERATION