Harman Kardon AVR 135 Owner's Manual

Also see for AVR 135: Brochure & specs Owner's manual Quick start guide Product View Owner's manual

Harman Kardon AVR 135 Owner's Manual Manual pdf 37 page image

PROGRAMMING THE REMOTE 37Programming the Remote2. Press the Volume Up button ) and notethat.the Program/SPL Indicator 2 will stopflashing and stay amber.3. Press either the AVR Selector 5 or theInput Selector 4, depending on whichsystem’s volume control you wish to have attachedfor the punch-through mode. The Program/SPLIndicator 2 will blink green three times andthen go out to confirm the data entry.Example: To have the AVR’s volume control acti-vated even though the remote is set to controlthe TV, first press the Video/TV Input Selector4 and the Mute button ( at the same time.Next, press the Volume Up button ), followedby the AVR Input Selector 5.NOTE: Should you wish to return the remote tothe original configuration after entering a VolumePunch-Through, you will need to repeat the stepsshown above. However, press the same InputSelector in steps one and three.Channel Control Punch-ThroughThe AVR’s remote may be programmed to operateso that the channel control function, performedwith the Sleep 9 and Surround A buttons,for either the TV, cable or satellite receiver used inyour system may be used in conjunction with oneof the other devices controlled by the remote. Forexample, while using and controlling the VCR,you may wish to change channels on a cable boxor satellite receiver without having to change thedevice selected by the AVR or the remote. To pro-gram the remote for Channel Control Punch-Through, follow these steps:1. Press the Input Selector button 4 for thedevice you wish to have the channel controlassociated with and the Mute button ( at thesame time until the red light illuminates under theInput Selector 4 and the Program/SPLIndicator 2 flashes amber.2. Press the Volume Down button ). TheProgram/SPL Indicator 2 will stop flashingand stay amber.3. Press and release the AVR 5 or InputSelector button 4 for the device that will beused to change the channels. The Program/SPLIndicator 2 will blink green three times andthen go out to confirm the data entry.Example: To control the channels using your TVwhile the remote is set to control the VCR, firstpress the VID 1/VCR Input Selector button 4and the Mute button ( at the same time. Next,release them and press the Volume Down button), followed by the same Input Selector but-ton 4.NOTE: To remove the Channel Control Punch-Through and return the remote to its original con-figuration, repeat the steps shown in the exampleabove. However, press the same Input Selectorin Steps 1 and 3.Transport Control Punch-ThroughThe AVR’s remote may be programmed to operateso that the Transport Control Functions P(Play, Stop, Fast Forward, Rewind, Pause andRecord) for a VCR, DVD or CD will operate in con-junction with one of the other devices controlledby the remote. For example, while using and con-trolling the TV, you may wish to start or stop yourVCR or DVD without having to change the deviceselected by the AVR or the remote. To program theremote for Transport Control Punch-Through, fol-low these steps:1. Press the Input Selector 4 for the deviceyou wish to have the channel control associatedwith and the Mute button ( at the same timeuntil the red light illuminates, under the InputSelector 4 and the Program/SPL Indicator2 flashes amber.2. Press the Play button P. The Program/SPLIndicator 2 will stop flashing and stay amber.3. Press and release the AVR 5 or InputSelector button 4 for the device that will beused to change the channels. The Program/SPLIndicator 2 will blink green three times andthen go out to confirm the data entry.Example: To control the transport of a CD playerwhile the remote is set to control the TV, press theVID 2/TV Input Selector button 4 and theMute button ( at the same time. Next, releasethem and press the Play button P, followed bythe CD Input Selector button 4.NOTE: To remove the Channel Control Punch-Through and return the remote to its original con-figuration, repeat the steps shown in the exampleabove. However, press the same Input Selectorin Steps 1 and 3.NOTE: Before programming the remote forVolume, Channel or Transport Punch-Through,make certain that any programming needed forthe specific TV, CD, DVD, Cable or SatelliteReceivers has been completed.Resetting the Remote MemoryAs you add components to your home-theatersystem, occasionally you may wish to totally repro-gram the remote control without the confusion ofany commands, macros or ”Punch-Through“programming that you may have done. To do this,it is possible to reset the remote to the originalfactory defaults and command codes by followingthese steps. Note, however, that once the remote isreset, all commands or codes that you haveentered will be erased and will need to be re-entered:1. Press any of the Input Selector buttons 4and the ”O“ button H at the same time untilthe Program/SPL Indicator 2 begins to flashamber.2. Press the ”3“ button H three times.3. The red LED under the Input Selector 4 willgo out and the Program/SPL Indicator 2 willstop flashing and turn green.4. The Program/SPL Indicator 2 will remaingreen until the remote is reset. Note that this maytake a while, depending on how many commandsare in the memory and need to be erased.5. When the Program/SPL Indicator 2 goesout, the remote has been reset to the factorysettings.