Harman Kardon AVR 330 Owner's Manual

Also see for AVR 330: Manual Brochure & specs Brochure & specs Service manual Reference guide

Harman Kardon AVR 330 Owner's Manual Manual pdf 37 page image

PROGRAMMING THE REMOTEPROGRAMMING THE REMOTE 37• When a button is pressed on the AVR 330 remote,the red light under the Input Selector ef forthe product being operated should flash briefly. Ifthe Device Control Selector flashes for some butnot all buttons for a particular product, it does NOTindicate a problem with the remote but rather thatno function is programmed for the button beingpushed.Volume Punch-ThroughThe AVR 330’s remote may be programmed to oper-ate the Volume Control and Mute func-tions of either the TV or the AVR 330 in conjunctionwith any of the devices controlled by the remote. Forexample, since the AVR 330 will likely be used as thesound system for TV viewing, you may wish to havethe AVR 330’s volume activated, although the remoteis set to run the TV. Either the AVR 330 or TV volumecontrol may be associated with any of the remote’sdevices. To program the remote for Volume Punch-Through, follow these steps:1. Press the Input Selector e for the unit you wishto have associated with the volume control and theMute Button at the same time until the redlight appears under the Input Selector e; theProgram/SPL Indicator c will flash amber.2. Press the Volume Up Button ; the Program/SPL Indicator c will stop flashing and stay amber.3. Press either the AVR Selector f or the InputSelector e, depending on which system’svolume control you wish to have attached for thepunch-through mode. The Program/SPL Indicatorc will blink green three times and then go out toconfirm the data entry.Example: To have the AVR 330’s volume controlactivated even though the remote is set to controlthe TV, first press the Video/TV Input Selectore and the Mute Button at the same time.Next, press the Volume Up Button , followedby the AVR Selector f.NOTE: Should you wish to return the remote to theoriginal configuration after entering a Volume Punch-Through, you will need to repeat the steps shownabove. However, press the same Input Selector inSteps 1 and 3.Channel Control Punch-ThroughThe AVR 330’s remote may be programmed to operateso that the channel control function for either the TV,cable or satellite receiver used in your system may beused in conjunction with one of the other devices con-trolled by the remote. For example, while using and con-trolling the VCR, you may wish to change channels on acable box or satellite receiver without having to changethe device selected by the AVR 330 or the remote.To program the remote for Channel Control Punch-Through, follow these steps:1. Press the Input Selector Button ef for thedevice you wish to have the channel control associ-ated with and the Mute Button at the sametime until the red light appears under the InputSelector ef and the Program/SPL Indicatorc flashes amber.2. Press the Volume Down Button . TheProgram/SPL Indicator c will stop flashingand stay amber.3. Press and release the Input Selector Button efor the device that will be used to change the chan-nels. The Program/SPL Indicator c will blinkgreen three times and then go out to confirm thedata entry.Example: To control the channels using your cablebox or satellite receiver while the remote is set tocontrol the VCR, first press the VID 1/VCR InputSelector Button e and the Mute Buttonat the same time. Next, release them and press theVolume Down Button , followed by the VID 2/TV Input Selector Button e.NOTE: To remove the Channel Control Punch-Throughand return the remote to its original configuration, repeatthe steps shown in the example above. However, pressthe same Input Selector in Steps 1 and 3.Transport Control Punch-ThroughThe AVR 330’s remote may be programmed to operateso that the Transport Control Functions ` (Play,Stop, Fast Forward, Rewind, Pause and Record) for aVCR, DVD or CD will operate in conjunction with one ofthe other devices controlled by the remote. For exam-ple, while using and controlling the TV, you may wish tostart or stop your VCR or DVD without having to changethe device selected by the AVR 330 or the remote. Toprogram the remote for Transport Control Punch-Through, follow these steps:1. Press the Input Selector ef for the deviceyou wish to have the channel control associatedwith and the Mute Button at the sametime until the red light appears under the InputSelector e and the Program/SPL Indicatorc flashes amber.2. Press the Play Button `. The Program/SPLIndicator c will stop flashing and stay amber.3. Press and release the Input Selector Button efor the device that will be used to change the chan-nels. The Program/SPL Indicator c will blinkgreen three times and then go out to confirm thedata entry.Example: To control the transport of a DVD playerwhile the remote is set to control the TV, first pressthe VID 2/TV Input Selector Button e and theMute Button at the same time. Next, releasethem and press the Play Button `, followed bythe DVD Input Selector Button e.NOTES:• To remove the Channel Control Punch-Through andreturn the remote to its original configuration, repeatthe steps in the example above. However, press thesame Input Selector in Steps 1 and 3.• Before programming the remote for Volume, Channelor Transport Punch-Through, make certain that anyprogramming needed for the specific TV, CD, DVD,cable or satellite receivers has been completed.• The AVR 330 remote is preprogrammed at thefactory so that the Transport Control Functions` operate the DVD player whenever the AVRdevice is selected.Reassigning Device Control SelectorsThe Input Selectors e are normally programmedto operate the product category shown on the remoteabove the button, but they may also be reassigned tooperate a second device of another type. The exceptionis the Video 3 Input Selector e (labeled “CBL/SAT”),which may be programmed to operate any device in theremote’s library.To program the remote so that the codes from oneproduct category are reassigned to a button wherethose codes are not normally associated (such as pro-gramming the Video 2 button, whose default is for theTV codes, to operate a second VCR or a personal videorecorder) follow these steps:1. Press the Input Selector e you wish to reassignand the Mute Button at the same timeuntil the red light appears under the Input Selectore and the Program/SPL Indicator cflashes amber.2. Press the Input Selector e for the device youwish to program into the reassigned button.3. Enter the three-digit code for the specific modelyou wish the reassigned button to operate.4. Press the same Input Selector e pressed inStep 1 once again to store the selection. The redLED under the reassigned Input Selector will flashthree times and then go out.42424238423842384238424238