Harman Kardon AVR 347 Owner's Manual

Also see for AVR 347: Brochure & specs Catalog Software upgrade instructions Worksheet Owner's manual

Harman Kardon AVR 347 Owner's Manual Manual pdf 54 page image

54 PROGRAMMING THE REMOTEExample: One blink, followed by a one-secondpause, followed by six blinks, followed by a one-second pause, followed by four blinks indicatesthat the code has been set to 164.For future reference enter the Setup Codes forthe equipment in your system here:DVD ____________ CD ________________VID1/VCR ________ VID3/TV __________VID2/CBL/SAT ______________________TAPE ______________________________VID4 ______________________________Learning Codes from a RemoteIn addition to using codes from the remote’sinternal code library, the AVR 347’s remote isable to “learn” codes from remotes that may notbe in the code library. In addition, you may usethis function to “learn over” the codes from apreprogrammed device to add functions notincluded in the preprogrammed codes. To learnor transfer codes from an IR remote to theAVR 347’s remote, follow these steps:1. Place the front of the original remote with thecode being sent so that it is facing the IRTransmitter Window 1 on the AVR 347remote “head-to-head.” The remotes should bebetween 2 and 4cm apart.2. Select the button on the remote that you wishto use as the device selector for the codes aboutto be entered. This must be any of the InputSelectors 4 or the AVR Selector 5. Notethat when new codes are learned with the AVR5 Selector, they may no longer control theAVR 347.3. Press the Input Selector 45 buttonchosen and the Learn Button at the sametime. Hold these buttons until the Program/SPLIndicator 2 flashes amber and the lightunder the device selector button turns red.Release the buttons. It is important that youbegin the next step within 20 seconds.4. Press the button on the AVR 347 remote thatyou wish to program. Note that the Program/SPL Indicator 2 will stop flashing.Important Note: Codes cannot be taught toall buttons on the remote. The buttons with thefollowing numbers are not learnable (fornumbers, see drawing on page 11): 4, 7,8, B, I, O, Q, , , , ,. In these cases the Program/SPLIndicator 2 keeps flashing after the buttonwas released.5. As long as the Program/SPL Indicator 2is on steadily (for five seconds), press and holdthe button on the original remote that you wishto “teach” into the AVR 347 remote. If youpressed the button too late or no command wasreceived within five seconds, the Program/SPLIndicator 2 will flash red three times andthen amber, then simply repeat step four. Whenthe Program/SPL Indicator 2 turns green,release the button on the original remote. Notethat the Program Indicator will then begin toflash amber again.NOTE: If the Program/SPL Indicator 2turns red steadily during Step 5, the program-ming was not successful. Repeat the steps to seeif the code will “take.” If the indicator keepsflashing red in step 5, this code cannot betaught.6. Repeat steps 4 though 5 for each button onthe source remote that you wish to transfer tothe AVR 347 remote.7. Once all codes have been transferred from theoriginal source remote to the AVR 347 remote,press the Learn button . This will turn off allLEDs and turn off the learning mode.8. Repeat Steps 1 through 7 for any additionalremotes you wish to “teach” into the AVR 347Remote.Erasing Learned CodesThe AVR 347’s remote allows you to remove orerase the code learned into a single button for asingle device, to remove or erase all the codesthat have been learned for a single device, or toerase all commands that have been learned to alldevices.To erase a single learned code fromwithin a single device’s settings, followthese steps:1. Press and hold both the Input Selector45 within which the individual button to beerased has been programmed and the Learnbutton .2. When the red LED under the Input Selectorturns red and the Program/SPL Indicator 2flashes amber, release the buttons.3. Press and release the Input Selector 45again for the device within which the individualbutton to be erased has been programmed.4. Press the 7 button H three times.5. Press and release the individual button forwhich the code is to be erased. TheProgram/SPL Indicator 2 will blink greentwo times and then return to amber.6. To erase other buttons within the same device,press them as noted in Step 5.7. When all buttons to be erased have beenpressed, press the Learn button to completethe process.To erase all codes within a single device,follow these steps:1. Press and hold both the Input Selector45 for which you wish to erase the codesand the Learn button .2. When the red LED under the Input Selectorturns red and the Program/SPL Indicator 2flashes amber, release the buttons.3. Press and release the same Input Selector45 again for the device whose codes youwish to erase.4. Press the 8 button H three times.5. The Program/SPL Indicator 2 will turn off,the red light under the Input Selector will flashon and off once and the Program/SPLIndicator 2 will flash green three times toindicate that the codes have been erased.To erase all codes that have been pro-grammed to all devices in the remote,follow these steps:1. Press any Input Selector 45 and alsothe Learn button .2. When the red LED under the Input Selectorturns red and the Program/SPL Indicator 2flashes amber, release the buttons.3. Press and release the same Input Selector45 again.4. Press the 9 button H three times.5. The Program/SPL Indicator 2 will turn off,the red light under the Input Selector will flashon and off once and the Program/SPLIndicator 2 will flash green three times aftersome seconds to indicate that the codes havebeen erased.Programming the Remote