Harman Kardon AVR 7550HD Service Manual

Also see for AVR 7550HD: Owner's manual Worksheet Quick start guide

Contents

INSTALLATION7. When a compatible code set is found, press the OK Button toprogram it into the Source Selector.8. Check that other functions control the device correctly. Sometimesmanufacturers use the same Power code for several models,while other codes vary. Repeat this process until you’ve pro-grammed a satisfactory code set that operates most functions.To change the device type of a Source Selector:If your system includes two products of one device type but noproduct corresponding to a different Source Selector, you mayprogram one product into its corresponding Source Selector, andchange another Source Selector’s device type to program thesecond product by following this procedure:1. Access the remote’s menu system by pressing and holding theAVR Settings Button for 3 seconds, until the “Main Menu” and“Program Device” messages appear in the LCD Display.2. Use the 1/5Buttons to select “Change Device Type” from theremote’s main menu, and press the OK Button.3. Use the 1/5 Buttons to select the Source Selector whose devicetype you wish to change, and press the OK Button. Your selectionwill appear on the left side of the lower line, while the choice ofnew device types will appear on the right side.4. Use the 1/5 Buttons to select the new device type you wish toassign to the Source Selector, and press the OK Button.5. Program your product into the Source Selector by choosing thebrand, then searching for a compatible code set, as described inthe preceding section. If you allow the remote to “time out”, thenthe device type reassignment will not take effect.To “learn” individual key codes:If some functions do not work correctly, you may reprogram individualkeys from the device’s original remote by following this procedure:1. Place the two remotes with their IR transmitters facing eachother, about one inch apart. See Figure 19.Figure 19 – AVR and Device Remotes “Head to Head”2. Access the remote’s menu system by pressing and holding theAVR Settings Button for 3 seconds, until the “Main Menu” and“Program Device” messages appear in the LCD Display.3. Use the 1/5Buttons to select “Learn” from the remote’s mainmenu, and press the OK Button.4. When the “Learn Menu” message appears in the upper line ofthe LCD Display, make sure the “Learn” message appears in thelower line (not “Learn Delete”), and press the OK Button.5. Use the 1/5Buttons to select the device you wish to learn acode for, and press the OK Button.6. Press the destination button, and the menu will prompt you topress the key on the original remote whose code you wish toprogram into the destination button. You may learn a new codeinto the following buttons: Device Power On/Off, AlphanumericKeys, Last Button, Back/Exit Button, Menu Button, NavigationButtons, OK Button, Disc Menu Button, the four Soft Keys,Channel Up/Down, Volume Up/Down, Mute and the TransportControls (including Record).NOTE: If you press the wrong destination button and wish tocancel the learning process, you must wait about 30 secondsfor the remote to “time out”. It will exit its program mode andreturn to normal operation, and you may begin again. Pressinganother button will have no effect.7. Press the key on the original remote, and if the code was learnedcorrectly, the Navigation and OK Buttons will light up. The LearnMenu will prompt you to learn another key, rename the key justlearned or exit Learn mode. Use the 1/5Buttons to make yourselection, and press the OK Button.To delete a programmed or learned code:1. Access the remote’s menu system by pressing and holding theAVR Settings Button for 3 seconds, until the “Main Menu” and“Program Device” messages appear in the LCD Display.2. Use the 1/5Buttons to select “Learn” from the remote’s mainmenu, and press the OK Button.3. When the “Learn Menu” message appears in the upper line ofthe LCD Display, scroll to the “Learn Delete” option, and pressthe OK Button.4. The Learn Delete menu offers the options of deleting a singlelearned key code, an entire device or all devices. Scroll to thedesired option and press the OK Button.• To delete an individual key code, the remote will first promptyou to select the device containing the key code, then promptyou to press the key. It will confirm the deletion, then offeryou the opportunity to delete another learned key or exit thedelete key function.• To delete an entire device, the remote will prompt you toselect the device. When you scroll to the device and pressthe OK Button, the remote will confirm the deletion and exitits programming mode, returning to normal operation.• To delete all devices, wait a few moments while the remotedeletes all programmed device codes. It will then return tonormal operation.To rename a key or device:If you wish to change the name of a device or key as it appears inthe LCD Display, follow these steps:1. Access the remote’s menu system by pressing and holding theAVR Settings Button for 3 seconds, until the “Main Menu” and“Program Device” messages appear in the LCD Display.2. Use the 1/5 Buttons to select “Rename” and press the OK Button.3. Use the 1/5 Buttons to select whether to rename a device or akey, and press the OK Button.4. Use the 1/5 Buttons to select the device, either to rename thedevice itself or a key function used by that device, and press theOK Button.5. The current name of the device or key will appear on the lowerline of the LCD Display, with the cursor at the end of the line.AVR 7550HD harman/kardon20