Contents - Table Of Contents
- Table Of Contents
- united kingdom telecommunications safety requirements
- radio protection for germany
- safety notices
- laser safety information
- about this book
- Chapter 1. Reference Information
- Front View with Covers, Later Models
- Rear View without Covers, Models 340, 34H, 350, 355, 360/36T, 365 370/37T, 375
- Front View without Covers, Early Models
- Front View without Covers – Model 397
- System Planar Connector Locations, Models 355, 365, 375
- System Planar Connector Locations Models 380 and 390
- System Planar Connector Locations Model 397
- Memory
- Data and Power Flow
- SCSI-Attached Disk Drives, Models 340, 34H, 350, 360/36T, 370/37T
- Data and Power Flow: SCSI Attached Disk Drives – Models 380, 390, 39H
- Data and Power Flow: SCSI Attached Disk Drives – Model 397
- Specifications (all models except 380, 390, 39H, and 397)
- Specifications Models 380, 390, 39H, and 397
- Power Cables
- Service Inspection Guide
- Chapter 3. Removal and Replacement Procedures
- Handling Static-Sensitive Devices
- Rear Cover
- Top Cover
- Front Cover
- Disk Drive (Bus-Attached): Models 320, 32E, 32H
- Disk Drive (SCSI-Attached): Models 320, 32E, 32H
- Disk Drive (SCSI-Attached): Models 340, 34H, 350, 355, 360/36T, 365 370/37T, 375
- Disk Drive: Models 380, 390, 39H, and 397
- Power Supply
- Power Supply (Models 380, 390, 39H, and 397)
- Diskette Drive
- Media Drive Removal for Models 380, 390, 39H, and 397
- Adapter Cards, Ethernet Riser Card, and External Diskette Riser Card
- Setting the Ethernet Riser Card Jumpers
- Attached Devices
- CPU Card
- CPU Card (Model 39H)
- Voltage Regulator Card (Model 39H)
- L2 Cache
- Fan and Air Duct (Model 39H Only)
- Memory Card
- Memory SIMMs
- System Planar
- Card Guide Frame
- Rear Fan
- Front Fan
- Key Lock
- Reset Switch
- Serial Ports Flex Circuit (Models 340, 34H, 350, 355, 360/36T, 365 370/37T, 375)
- Serial Port (Models 380, 390, 39H, and 397)
- Three-Digit Display: Models 320, 32E, 32H
- Three-Digit Display Models 340, 34H, 350, 355, 360/36T, 365 370/37T, and 375, 380, 390, 39H
- Three-Digit Display, Model 397
- Toroids
- Battery
- Contact Strips (Models 340, 34H, 350, 355, 360/36T, 365, 370/37T, 375)
- Chapter 4. System Installation
- Index
- Appendix A. SCSI Device Address Record
| 
Removal and Replacement Procedures 3-55Three-Digit Display Models 340, 34H, 350, 355, 360/36T, 365,370/37T, and 375, 380, 390, 39HRemoval 1. Set the power switches of the attached devices to Off.2. Set the power switch of the system unit to Off and unplug the external power cable.3. If the system unit has a rear cover, do the rear cover removal procedure on page 3-3.4. Do the top cover removal procedure on page 3-4.5. On all models except 380, 390, and 39H, do the front cover removal procedure on page3-6.6. On models 380, 390, and 39H, do the card guide frame removal procedure on page3-43.7. Pull up on the connector handle of the three-digit display.8. To remove the three-digit display from the card guide, push the back of the display whiletwisting and pulling the display from the front.Replacement1. While aligning the flex-circuit cable in its plastic guide shield, twist and push thethree-digit display into the card guide frame.2. On models 380, 390, and 39H, do the card guide frame replacement procedure on page3-43.3. Push the 3-digit display connector into the planar connector.4. On all models except 380, 390, and 39H, do the front cover replacement procedure onpage 3-6.5. Do the top cover replacement procedure on page 3-4.6. If the system unit has a rear cover, do the rear cover replacement procedure on page7. Set the power switches of the attached devices to On.8. Set the power switch of the system unit to On and plug in the external power cable.ConnectorHandle |
