Contents - Table Of Contents
- Table Of Contents
- united kingdom telecommunications safety requirements
- radio protection for germany
- safety notices
- laser safety information
- about this book
- Chapter 1. Reference Information
- Front View with Covers, Later Models
- Rear View without Covers, Models 340, 34H, 350, 355, 360/36T, 365 370/37T, 375
- Front View without Covers, Early Models
- Front View without Covers – Model 397
- System Planar Connector Locations, Models 355, 365, 375
- System Planar Connector Locations Models 380 and 390
- System Planar Connector Locations Model 397
- Memory
- Data and Power Flow
- SCSI-Attached Disk Drives, Models 340, 34H, 350, 360/36T, 370/37T
- Data and Power Flow: SCSI Attached Disk Drives – Models 380, 390, 39H
- Data and Power Flow: SCSI Attached Disk Drives – Model 397
- Specifications (all models except 380, 390, 39H, and 397)
- Specifications Models 380, 390, 39H, and 397
- Power Cables
- Service Inspection Guide
- Chapter 3. Removal and Replacement Procedures
- Handling Static-Sensitive Devices
- Rear Cover
- Top Cover
- Front Cover
- Disk Drive (Bus-Attached): Models 320, 32E, 32H
- Disk Drive (SCSI-Attached): Models 320, 32E, 32H
- Disk Drive (SCSI-Attached): Models 340, 34H, 350, 355, 360/36T, 365 370/37T, 375
- Disk Drive: Models 380, 390, 39H, and 397
- Power Supply
- Power Supply (Models 380, 390, 39H, and 397)
- Diskette Drive
- Media Drive Removal for Models 380, 390, 39H, and 397
- Adapter Cards, Ethernet Riser Card, and External Diskette Riser Card
- Setting the Ethernet Riser Card Jumpers
- Attached Devices
- CPU Card
- CPU Card (Model 39H)
- Voltage Regulator Card (Model 39H)
- L2 Cache
- Fan and Air Duct (Model 39H Only)
- Memory Card
- Memory SIMMs
- System Planar
- Card Guide Frame
- Rear Fan
- Front Fan
- Key Lock
- Reset Switch
- Serial Ports Flex Circuit (Models 340, 34H, 350, 355, 360/36T, 365 370/37T, 375)
- Serial Port (Models 380, 390, 39H, and 397)
- Three-Digit Display: Models 320, 32E, 32H
- Three-Digit Display Models 340, 34H, 350, 355, 360/36T, 365 370/37T, and 375, 380, 390, 39H
- Three-Digit Display, Model 397
- Toroids
- Battery
- Contact Strips (Models 340, 34H, 350, 355, 360/36T, 365, 370/37T, 375)
- Chapter 4. System Installation
- Index
- Appendix A. SCSI Device Address Record
| 
4-2 Installation and Service GuideStep 2. Observe this Safety Notice during InstallationNote: For a translation of the following notices, seeSystem Unit Safety Information, OrderNumber SA23-2652.DANGERAn electrical outlet that is not correctly wired could place hazardous voltageon metal parts of the system or the devices that attach to the system. It is theresponsibility of the customer to ensure that the outlet is correctly wired andgrounded to prevent an electrical shock.Before installing or removing signal cables, ensure that the power cables for thesystem unit and all attached devices are unplugged.When adding or removing any additional devices to or from the system, ensurethat the power cables for those devices are unplugged before the signal cablesare connected. If possible, disconnect all power cables from the existing systembefore you add a device.Use one hand, when possible, to connect or disconnect signal cables to prevent apossible shock from touching two surfaces with different electrical potentials.During an electrical storm, do not connect cables for display stations, printers,telephones, or station protectors for communications lines.CAUTION:This product is equipped with a 3-wire power cable and plug for the user’s safety. Usethis power cable in conjunction with a properly grounded electrical outlet to avoidelectrical shock.DANGERTo prevent shock hazard, disconnect the power cable from the electrical outletbefore relocating the system. |
