JAI CM-200GE User Manual

Also see for CB-200GE: User manual

Contents

JAI CM-200GE User Manual Manual pdf 54 page image

CM-200 GE / CB-200 GE- 53 -12.2. Specification tableSpecifications CM-200GE CB-200GEScanning system Progressive scanFrame rate full frame 24.98 frames/sec. Progressive (1236 lines/frame)Pixel clock 65 MHzLine frequency 31.25 kHz ( 1H = 32 μs )(2080 pixel clock/line)CCD sensor 1/1.8”. Monochrome ICX274AL 1/1.8” Bayer Color ICX274AKSensing area 7.13 (h) x 5.37 (v) mm 1/1.8 inch diagonalCell size 4.4 (h) x 4.4 (v) μmActive pixels 1624 (h) x 1236 (v)Pixels in video output.Full Scan2/3 partial Scan1/2 partial Scan1/4 partial Scan1/8 partial ScanVertical BinningRegion-of-interest (ROI)1624 (h) x 1236 (v) 24.98 fps. H = 31.25 kHz1624(h) x 891 (v) 35.19 fps H= 31.25 kHz1624 (h) x 712 (v) 43.89 fps. H = 31.25 kHz1624 (h) x 451 (v) 69.75 fps. H = 31.25 kHz1624 (h) x 319 (v) 98.89 fps. H = 31.25 kHz1624 (h) x 627 (v) 44.49 fps. H = 27.9 kHz ( *Note)User Definable. Memory read-out*Note: Vertical binning is for CM-200GE onlySensitivity on sensor (minimum) 0.21 Lux (Max. gain, Shutter OFF, 50%video )0.7 Lux (Max. gain, Shutter OFF,50%Green, w/IR cut filter)S/N ratio More than 50 dB (0dB gain)Digital Video output. GigE Vision CompliantMono8,Mono10,Mono10_Packed GigE Vision CompliantBAYRG8,BAYGB8,BAYRG10,BAYGB10Iris video output. Analogue 0.7 V p-p , enabled by internal switchGain Manual -3 to +12 dBSynchronization Internal X-talGPIO ModuleInput/output switchClock Generator ( One)Pulse Generators ( Four)Configurable 14-in / 9-out switch12-bit counter based on 25MHz clock or Pixel clock20-bit counter programmable for length, start point, stop point, repeatHardware Trigger modes Edge Pre-Select , Pulse Width Control, Frame Delay and SequenceOB area transfer mode ON / OFFEvent message SYNC / ASYNC mode ( Trigger mode status when exposure starts )Exposure start, Exposure end, Trigger IN, Video start, Video endElectronic ShutterPreset Shutter speedProgrammable exposureExposure Time (Abs)GPIO plus Pulse WidthOFF(1/31) and 1/60 to 1/10,000 in 9 steps2L(64μs) to 1250L ( 40.032ms) in 1L stepsμsec – user definable. Same range as PEmax. 2 sec ( Can be set by 100μs unit or Pixel Clock unit)Control interface Register based. GigE Vision / GenIcam compliantFunctions controlled via GigEVision InterfaceShutter, Gain, Black Level, Trigger mode, Read out mode,GPIO setup ,ROI ( GenIcam mandatory functions )GigE Vision Streaming Control Packet size, Delayed ( Frame ) read-out, inter-packet delayJumbo frame can be set at max. 4K(4040) , Default packet size is 1428 Byte.Indicators on rear panel Power, Hardware trigger, GigE Link, GigE activityOperating temperature -5°C to +45°CHumidity 20 – 90% non-condensingStorage temp/humidity -25°C to +60°C/20% to 90% non-condensingVibration 10G (20Hz to 200Hz, XYZ)Shock 70G