Jabra GN9300e User Manual
Also see for GN9330e - USB - Headset: Guide for basic set-up and useUser manualUser manualSpecificationsSetup guide
              | |
12GN9350e GN9330e GN9330e USB4.6 Switching a call from desk telephone handset to headsetIt’s possible to switch a call in progress from the telephone’s handset to the headset:1. Remove the headset from base, or if already out, press the headset’s talk button.This establishes a link.–> The headset’s link indicator will start flashing and the call will be switched to the headset.Note: Do not place handset before the call is over, as this will end the call.GN9350e GN9330e GN9330e USB4.7 New master headset pairing to baseYou may designate a new master headset for your base.Important: Before designating a new master headset, ensure that the original headset’s link to the base unit isclosed by pressing its talk button. The telephone or USB indicator should not flash.To designate a new master headset:1. Place the new master headset into the charging cradle of the base.2. Press the base’s pairing button.–> Both the telephone and USB mode buttons on thebase, and the headset’s link indicator, will light for2 seconds. This indicates successful pairing of the newmaster headset.GN9350e GN9330e GN9330e USB4.8 Establishing a Clean Audio Mode linkIn the PC phone (VoIP) use case many UnifiedCommunication applications (e.g. Cisco IP Communicatoror Microsoft® Lync™ 2010) deliver voice mails in the inboxof the e-mail application (e.g. Outlook).Further, many users have a separate application for conferencecalls (with or without video). In these use case it is also very relevant to use your headset.In situations where other applications than the PC phone applicationwants to use the headset (as just described), you need to establisha Clean Audio Mode link without triggering the soft phone hook-offcommand.The Clean Audio Mode functionality is implemented as a double-tapon the headset’s talk button.For example, if you want to participate in a conference call or listen to a voice-mail delivered byemail, simply activate the Clean Audio Mode by double-tapping the headset’s talk button onthe headset. When ending the conference call just single tap the headset’s talk button to closethe Clean Audio Mode.Note: that you have to set the Audio Preference in the Windows operation system to the GN9330e or GN9350e.Also, in the conference call application (e.g. Windows Live Meeting), you have to set the Audio preferences to theGN9330e or GN9350e.5. Use with DECT cordless telephonesGN9350e GN9330e GN9330e USBYour headset can also be used with DECT cordless telephones (Digital Enhanced CordlessTelecommunication), which are GAP-compatible (Generic Access Profile). You must first pair theheadset to the base unit of the cordless telephone.Important: Your headset’s authentication code is 0000, which is the same code as for most DECTcordless telephones. Your headset will only work with cordless telephones with the 0000 code.To pair your headset to your DECT cordless telephone:1. Press and hold down the headset’s talk button and mute button (at tip of volume control)for 5 seconds.–> The headset’s link indicator will flash rapidly.2. Activate the cordless telephone’s GAP mode. Consult your cordless telephone’s manual GAPcompatibility/pairing instructions.–> The headset’s link indicator will light for 2 seconds to indicate successful pairing. Yourheadset is now ready to use with your cordless telephone. Consult your cordless telephone’suser manual for using your headset with your cordless telephone.3. Note that the headset must be re-paired to the GN9350 base to resume normal operation.6. Replacing the battery pack (GN accessory)GN9350e GN9330e GN9330e USB6.1 Adding extra battery charging facilityAn extra battery charging facility is available as an accessory. This canbe attached to your base to allow you to charge an extra battery.To add the extra battery charging facility cover:1. Remove the blind cover from the base by sliding it upward untilremoved.2. Slide the extra battery charger into the base charge tower until it clicks in place.The extra battery can be charged in its receptor on the back of the charge tower. An indicatorabove the receptor will light when the battery is placed correctly and is charging. The indicatorwill turn off when battery is fully charged.16 17 |
Related manuals for Jabra GN9330e - USB - Headset
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine