Jabra M5390 User Manual
Also see for M5390: Setup guideUser manualDatasheetSpecificationsDatasheet
16English17 English10. Using the Jabra M5390 Multiuse headset with multiple Bluetooth®-enabled devicesYour Jabra M5390 Multiuse headset can be paired with up to 8 devices. However, only two can beconnected (paired with the headset, turned on and in range) with the headset at one time. This couldbe any two Bluetooth® devices (for example, a cell phone and the Jabra M5390 Multiuse base, or theJabra A335w Dongle and a cell phone, or two cell phones). Therefore, if the headset is in range ofthe Jabra M5390 Multiuse base or Jabra A335w Dongle, only one additional Bluetooth® device can beconnected to the headset (paired with the headset, turned on and in range).The headset is by default paired with the base and the dongle. This means that the headset willautomatically connect to these two devices from the factory if in range and turned on. Therefore, if a cell phoneneeds to be connected to the headset, either the dongle or base has to be turned off or placed out of range.It is also possible to have two Bluetooth®-enabled cell phones connected to the Jabra M5390 Multiuseheadset simultaneously. In this case, both the base and the dongle should be disconnected from theheadset.11. Operating devices in multiuse scenariosUsing the button interface of the headset, it is possible to operate both connected devices in amultiuse scenario (the two devices connected to the headset). Operations can be divided intoreceiving incoming and placing outgoing calls.If receiving an incoming call from either of the connected devices, this device will automatically bethe device “in use” and a tap of the button will answer the call. Press the buttone to cancel the call.If you would like to place an outgoing call activated from the headset, you must manually placeone of the devices “in use”. When a device is placed “in use“, everytime a button is pressed onthe headset, the instruction is sent to the selected device. For example, if you wish to make a callusing Voice Dial on the second connected device, you must first make sure that the second deviceis “in use”. After confirming the device is “in use“, simply tap the button to activate Voice Dial.In order to switch between the two connected devices, press the Answer/End button forapp. 1.5 seconds.After swaping the “in use“ status of two devices, different indicators will be used to indicatewhich device is now “in use”; When activating the Jabra A335w dongle as “in use“, the LED of thedongle will give 5 quick light-blue flashes. Also the speaker of the headset will say “Dongle infocus”. When activating the Jabra M5390 base as “in use“, the LED on the base will give 5 quicklight-blue flashes. Also the speaker of the headset will say “Base in focus”. When activating a cellphone as “in use“ the speaker of the headset will say “Mobile in focus”.Please note that this only applies to multiuse scenarios. If the headset is only connected to onedevice, then this device will automatically be “in focus”.Also note that the Last Number Redial command does not use the “in focus” concept. Upondouble tapping the Answer/End button, the Last Number Redial command will automaticallybe sent to the connected device with the most recent incoming call (which was received whileconnected to the headset).12. Switching between the base and the Jabra A335w Dongle in a multiuse scenarioA typical multiuse scenario is to have the headset connected to one cell phone and either thebase or the dongle. If you wish to switch the between base and dongle, while maintaining thecell phone connection, just press and hold the Volume up/down button for 4 seconds.13. Troubleshooting & FAQQ: Nothing happens when I try to adjust the clear dial tone.A: Make sure the base is tunning at full power (the visual indicator on the base unit is a steadygreen). Then establish a voice link between base and headset (visual indicators on base unitand headset will be flashing green). Also ensure that the telephone is activated (the handset isoff the hook or the “line” button is pressed).Q: I hear myself when I talk.A: Your transmit volume level (please refer to section 3.10) is probably too high.Turn down the transmit volume level (3->2, 2->1).Q: The sound through the headset is of poor quality or the person at the other end cannot hear me.A: Make sure that you have positioned the clear dial tone switch correctly. To do this, call someoneas a test case, and adjust the clear dial tone switch.Q: When I press the Answer/End button, the GN 1000 RHL lifts, but the call is not connected.A: Make sure that you are using the telephone’s handset port and not the headset port(if your telephone has one), when using a GN 1000 RHL for remote answering.Q: I have moved desks at work. Is it possible to put my headset on another base?A: Yes, this is possible. The headset only needs to be paired to the new base. Just follow theprocedure as described in section 9 of this guide.Q: I cannot hear anything in my headset when using my cell phone.A: - Increase the volume on the headset (or phone).- As the volume level needed might vary between your desk phone and cell phone, it might bebest to adjust the level on the phones.- Then use the headset volume level adjustments for general adjustments (but ensure that theheadset is paired with the cell phone).- Make sure that the phone is connected to the headset - if it does not connect either fromthe phone’s Bluetooth ® menu or by tapping the Answer/End button, follow the pairingprocedure (see section 4 “Pairing your headset with your cell phone” in this guide).NOTE:When multiple Bluetooth-enabled devices are paired with the headset, the Voice Dial*function will work with the last device that was paired.*If the cell phone supports this feature. |
Related manuals for Jabra M5390
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine