Jacuzzi Delos Pro Use & Maintenance

Also see for DELFI PRO: Installation manual Instructions for preinstallation Instructions for preinstallation Installation manual

Contents

27XPress the “Up” or “Down” key again to change the dis-played value from a minimum of 15 °C to a maximum of 40 °C(59÷104 °F).XTo show the temperature of the water in the tub again, donot touch any key for about 5 seconds.”Energy savings” modeThis function makes it possible to maintain the water temperature10 °C (50 °F) below the set temperature for a certain period of time.XPress the “Econo” key. The display shows the messageEdx, where “x” indicates the duration in hours.XUse the “Up” or “Down” keys to enter the desired dura-tion, from a minimum of 0 to a maximum of 24, which means thefunction is always on.XPress the “Econo” key again to confirm the selected value.You will then go to the start time (Edx).XFirst set the hour and confirm with the “Econo” key. Then setthe minutes, and press the “Econo” key again to memorize theset values and exit programming.When the function is on, the display will shown the respectivesymbol.XTo deactivate the function, set the duration time to 0 (zero).NOTES- The minimum temperature that characterizes “energy savings”mode may never be less than 15 °C (59 °F) (minimum maintenancetemperature).- If there is a power outage, the set data are stored in memory. Ho-wever, when the power comes back on, the function does not resu-me. Rather, it is turned on at the set start time.Maintenance of minimum temperature of water in tub andanti-freeze protection of the pipes (“Smart Winter”).The system software of your spa is designed to provide efficient,rational management of any hazardous situations which may oc-cur due to excessively cold temperatures and freezing of the water.For further information on water heating and system safe-guards, refer to the product’s installation manual.NOTE: when the anti-freeze protection is active, the display willshow the message ICE.Abnormal operating conditions- alarm signals -Alarms are indicated on the display, with the corresponding errorcode. You will continue to see the code if the alarm conditionpersists.Here is a list of the various alarms that may appear. Refer to theproduct’s installation manual for a detailed description of the vari-ous messages that may appear on the display.X“FLC”In some models, the initials “FLC” may appear on the display.- Contact an authorized Jacuzzi® service centre.X“FLO” (flashing)The heater does not turn on.- The system attempts to reactivate the heater three times.X“FLO” (stable)The heater cannot be reactivated.- Try turning the switch up the line from the spa off and backon; if the signal stays on, contact an authorized Jacuzzi® servicecentre.X“HOH” The measured temperature at the heater is 48 °C (118 °F)or higher (the heater is turned off).DO NOT ENTER THE WATER- If the alarm condition persists, try turning the switch up the linefrom the spa off and back on. If the signal stays on, contact anauthorized Jacuzzi® service centre.X“Ho” Excessive water temperatureDO NOT ENTER THE WATER- If present, remove cover from spa.- If the excessive temperature increase is due to sunlight, addcold water to the spa.When the temperature has dropped to below 43 °C (109 °F), thespa should re-activate automatically. If it does not, disconnectthe power supply and contact an authorized Jacuzzi® servicecentre.X“rPF” Defective temperature probe.DO NOT ENTER THE WATERIt is not possible to activate any function.- Contact an authorized Jacuzzi® service centre.X“HPF” Activation of safety thermostat.It is not possible to activate the electric heater.The electric heater has been deactivated due to overheating. Thismay be due to irregular water flow.- Try turning the switch up the line from the spa off and backon (system reset). If the signal stays on, contact an authorizedJacuzzi® service centre.