Jacuzzi Finestra FL61000 Installation & Operation Instructions

Also see for Finestra 6030: Specification sheet

Contents

Jacuzzi Whirlpool Bath: finestra Walk-in Bath Page 1 fl61000B • 10/07Cleaning the BathTo clean your bath, simply use a mild, nonabrasive liquiddetergent solution. You can protect and restore the gloss to adulled acrylic surface by applying Meguiar’s #10 Mirror Glaze,a product specifically designed for use on acrylic finishes. IfMeguiar’s is not available, an acrylic polish of equal quality orautomotive paste wax is acceptable.never use abrasive household cleaners on any JacuzziWhirlpool Bath product.repairs to the surfaceMinor scratches which do not penetrate the color finish can beremoved by lightly sanding with 600-grit wet/dry sandpaper.Restore the gloss using Meguiar’s Mirror Glaze or automotivepaste wax.Major scratches and gouges which penetrate the acrylicsurface will require refinishing. Ask your Jacuzzi WhirlpoolBath dealer for special instructions.Bath additivesnote: Do not use oil or oil-based bath additives.If you want to use any kind of bath additive, use only a smallamount of low-foaming powder or crystal substance; thewhirlpool action intensifies the foaming properties of soaps.The use of certain bath oils, bubble baths and bath additivesmay increase the level of accumulations of bath residue in thewhirlpool system. If excess accumulations persist, you shoulddiscontinue use of these products.Purging the Whirlpool systemnote: The Whirlpool System should be purged at least twicea month.To remove accumulations of bath residue from the whirlpoolsystem, it is recommended that a whirlpool bath be purgedat least twice a month. For best results, however, werecommend that you purge your whirlpool bath after eachuse using, Systems Clean™, our exclusive two-part plumbingsystem cleaner made specifically for whirlpool baths.Systems Clean™ is available through an authorized JacuzziWhirlpool Bath distributor or by calling us direct at 1-800-288-4002.systems Clean™ instructionsRefer to the instructions on the Systems Clean™ packet.CaUtion: Do not use while bathing! Use extreme cautionwhen handling this product!Immediately after bathing and exiting the whirlpool bath,leave the bath water in the tub and add more hot water. Thewater level in the tub must be at least 2” (5,08 cm) above thehighest jet.note: Inducted air from the hydromassage system will causethe Systems Clean™ contents to foam increasing odor.Turn OFF the whirlpool air control or turn it to the lowestsetting and pour in the entire contents of PACkET #1 ONLYdirectly into the bath water. For best results, pour the SystemClean into the tub near the intake for the circulation pump andbe sure to avoid contact with your skin. Allow the whirlpoolto run for 30 seconds and then add PACkET #2 ONLY. it isimportant to use Packet #1 before Packet #2 to avoid astrong odor. Allow the bath to run for 5 to 10 minutes thendrain the tub completely. Refill the tub with cold water and runfor 2 to 3 minutes. Drain completely and rinse off any residue.Remember to reset the air valves to your bathing comfortlevel.Danger: Harmful if swallowed. Eye irritant. Protect youreyes, skin and mucus membranes from contact with thisproduct or its concentrated solution. A strong alkaline productcan cause severe burns to the eyes and skin.If you have followed the standard purging instructions aboveand still have an excess accumulation of bath residue anddesire an alternative cleaning mechanism, we recommendsUPer sYsteMs Clean™ PlUs manufactured by StearnsPackaging to rectify this condition. This may be obtained bycontacting us at 1-800-288-4002. It is recommended thatyou follow the instructions provided by the manufacturerwith the product. Repeated use may be necessary. sUPersYsteMs Clean™ PlUs does not replace the necessity toregularly purge your whirlpool system with Systems Clean™as recommended.ozone MaintenanceThe PrO3 Ozone Sanitation System is a maintenance-freesystem. All that is required is the regular system cleaningusing the Systems Clean™ as directed.MaintenanCe