Jacuzzi SALON Installation And Operating Instructions Manual

Contents

ENGLISH16Jacuzzi Whirlpool Bath EL21000B 10/06Drain InformationA drain/overflow assembly (sold separately) must be installedon the bath, water tested, and connected to the sanitary systemof the house. After opening the carton, inspect for damage andverify that the kit is of the proper finish. In the Jacuzzi WhirlpoolBath drain/overflow kit (supplied with some models), note thatthe waste flange, strainer, overflow cover and cover screwsare packaged in a separate package within the kit to protectthe trim finish. Follow the installation instructions providedwith the drain/overflow kit. After the drain is fully installed,test for proper drainage. If the unit does not drain properly,rectify this condition before proceeding with the installation.Jacuzzi Whirlpool Bath is not responsible for removal and orreinstallation costs.NOTE: Watertight installation of the drain is the installer’sresponsibility. Drain leakage is excluded from the JacuzziWhirlpool Bath warranty of this product.NOTE: FUZION™ TUBS ONLY - The supplied overfl owfi tting of the drain/overflow assembly MUST be installedbefore the wood frame or (for undermount tubs) thecounter is installed.Plumbing and Water SupplyPlumbingPump, jets, and suction fittings for the whirlpool system arefactory plumbed in schedule 40 PVC piping.All Jacuzzi Whirlpool Salon™ Spa Bath products are factorytested for proper operation and watertight connections prior toshipping. If leaks are detected, notify your Jacuzzi WhirlpoolBath Dealer. Do not install the unit.Water SupplyConsult local authorities for plumbing code requirementsin your area.IMPORTANT: Proper installation of the fill spout plumbingand compliance with local codes are the responsibilityof the installer. Jacuzzi Whirlpool Bath does not war-rant connections of water supply fittings and piping, fillsystems, or drain/overflow systems. Nor is it responsiblefor damage to the bath which occurs during installation.CAUTION: A nonflammable protective barrier must beplaced between soldering work and bath unit to preventdamage to the bath.*ANTI-SIPHON VALVEBATH RIM 6" * NOTPROVIDEDAnti-Siphon Valve (Optional)Optional Anti-Siphon valve installation. The Anti-Siphonvalve is not supplied with the tub. Consult your local plumb-ing code requirements for the minimum height above the tubrim.Fuzion™ Overfl ow Fitting InstallationThe supplied overflow fitting of the drain/overflow assemblyMUST be installed before the wood frame or (for undermounttubs) the counter is installed.Remove and open the overflow fitting from the drain kit (sup-plied). Remove washers and nuts from the overflow fitting.Place a small bead of plumbers putty, silicone, or similarapproved sealant around the underside of the top flange. Placethe overflow fitting into the overflow hole of the tub.From the underside of the unit, place the rubber washerthen locknut on the fitting and tighten securely. Be carefulnot to over tighten.The 1-1/2" (38 mm) overflow fitting connects with standarddrain plumbing fittings widely available at local hardware andplumbing stores. Assemble in accordance with local plumbingor building codes.After the drain is fully installed, test for proper drainage. Ifthe unit does not drain properly, rectify this condition beforeproceeding with the installation. Jacuzzi Whirlpool Bath is notresponsible for removal and or reinstallation costs.NOTE: Watertight installation of the drain is the installer’sresponsibility. Drain leakage is excluded from the JacuzziWhirlpool Bath warranty of this product.Clean-Up After InstallationTo avoid dulling and scratching the surface of the bath,never use abrasive cleaners. A mild liquid detergent and warmwater will clean soiled surfaces.Remove spilled plaster with a wood or plastic edge. Metaltools will scratch the surface. Spots left by plaster or groutcan be removed if lightly rubbed with detergent on a dampcloth or sponge.Paint, tar, or other difficult surface stains can be removedwith paint thinner, turpentine, or isopropyl alcohol (rubbingalcohol). NOTE: Use these chemicals only on SURFACEstains.Minor scratches which do not penetrate the color finish canbe removed by lightly sanding with 600-grit wet/dry sandpaper.You can restore the glossy finish to the acrylic surface of thebath with a special compound, Meguiar's #10 Mirror Glaze.If that is not available, use automotive rubbing compound fol-lowed by an application of automotive paste wax.Major scratches and gouges which penetrate the acrylicsurface will require refinishing. Ask your Jacuzzi WhirlpoolBath dealer for special instructions or visit our web site athttp://www.jacuzzi.com/ to find a service agent listing for Sur-face or Shell-Related Problems.OVERFLOWFITTINGAPPLYPUTTY/SEALANT(NOT PROVIDED)FLAT RUBBER WASHERLOCKNUTTIGHTWASTE ELBOW(NOT PROVIDED)