Jenn-Air 30" WALL-MOUNT CANOPY RANGE HOOD Installation Instructions And Use & Care Manual

Also see for 30" WALL-MOUNT CANOPY RANGE HOOD: Installation Instructions and Use & Care Guide Installation Instructions and Use & Care Guide Installation & use manual Installation Instructions and Use & Care Guide

Jenn-Air 30" WALL-MOUNT CANOPY RANGE HOOD Installation Instructions And Use & Care Manual Manual pdf 5 page image

5INSTALLATION REQUIREMENTSTools and PartsGather the required tools and parts before starting installation.Read and follow the instructions provided with any tools listedhere.Tools needed■ Level■ Drill with 1¼" (3.0 cm), ³⁄₈" (9.5 mm), ⁷⁄₆₄" (2.75 mm) and¹⁄₈" (3.0 mm) drill bits■ Pencil■ Wire stripper or utility knife■ Tape measure or ruler■ Pliers■ Caulking gun and weatherproof caulking compound■ Vent clamps■ Jigsaw or keyhole saw■ Flat-blade screwdriver■ Metal snips■ Phillips screwdriverParts needed■ Home power supply cable■ ½" (12.7 mm) UL listed or CSA approved strain relief■ 3 UL listed wire connectorsFor vented installations, you will also need:■ 1 wall or roof cap■ Metal vent systemFor non-vented (recirculating) installations, you will alsoneed:■ Recirculation Kit Part Number W10272064 for non-vented(recirculating) installations only. See “Assistance or Service”section to order.Parts suppliedRemove parts from packages. Check that all parts are included.■ Hood canopy assembly with ventilator and light bulbsinstalled■ 2 glass mounting brackets■ Vent transition with back draft dampers installed■ Blower support bracket■ Glass mantle■ Vent cover support bracket (3 pieces)■ Mounting template■ 2-piece vent cover■ 2 - 2.9 x 6.5 mm screws■ 8 - 4 x 8 mm screws■ 6 - 5 x 45 mm mounting screws■ 2 - 8 x 40 mm wall anchors■ 4 - 10 x 50 mm wall anchorsLocation RequirementsIMPORTANT: Observe all governing codes and ordinances.Have a qualified technician install the range hood. It is theinstaller's responsibility to comply with installation clearancesspecified on the model/serial rating plate. The model/serial ratingplate is located behind the left filter on the rear wall of the venthood.Canopy hood location should be away from strong draft areas,such as windows, doors and strong heating vents.Cabinet opening dimensions that are shown must be used. Givendimensions provide minimum clearance.Grounded electrical outlet is required. See “ElectricalRequirements” section.The canopy hood is factory set for venting through the roof orwall. For non-vented (recirculating) Installation see “For Non-vented (recirculating) Installations” in “Connect Vent System”section. Recirculation Kit Part Number W10272064 is availablefrom your dealer or an authorized parts distributor.All openings in ceiling and wall where canopy hood will beinstalled must be sealed.For Mobile Home InstallationsThe installation of this range hood must conform to theManufactured Home Construction Safety Standards, Title 24CFR, Part 328 (formerly the Federal Standard for Mobile HomeConstruction and Safety, Title 24, HUD, Part 280) or when suchstandard is not applicable, the standard for Manufactured HomeInstallation 1982 (Manufactured Home Sites, Communities andSetups) ANSI A225.1/NFPA 501A, or latest edition, or with localcodes.Product Dimensions*For non-vented (recirculating) installations14 ⁷⁄₈"(37.8 cm)12 ³⁄₄"(32.3 cm)35" (88.9 cm) min.*60 ³⁄₄" (154.3 cm) max.56 ⁵⁄₁₆" (143.0 cm) max.28"(71.7 cm)19 ³⁄₄"(50 cm)30" - 36"(76.2 cm - 91.4 cm)