Jenn-Air JB36NXFXLW00 Technical Education

Also see for JB36NXFXLW00: Installation guide User & care guide Use & care guide

Contents

Jenn-Air JB36NXFXLW00 Technical Education Manual pdf 28 page image

2-1820NOTE: To achieve a flush installation, it is critical to verify a ³⁄₄"(1.9 cm) depth from the front face of the adjacent cabinetry tothe refrigerator.Level and Align RefrigeratorIMPORTANT: All four leveling legs must contact the floor tosupport and stabilize the full weight of refrigerator. Rollers are formoving refrigerator and not for permanent support.After moving the refrigerator to its final location:1. Use a ⁵⁄₁₆" socket driver to turn the leveling bolts clockwise toextend the legs to the floor as shown. The rollers should be offthe floor.2. Adjust the leveling legs to level and align the refrigerator fromleft to right and front to back so that the refrigerator is leveland aligned with the cabinets.3. Continue adjusting all of the leveling legs to raise therefrigerator until the top is within at least ¹⁄₄" (6.35 mm) of thetop soffit as shown.NOTE: If an anti-tip board has been used, adjust the levelinglegs until the top of the refrigerator is making contact with thebottom of the anti-tip board(s). Do not crush the compressorcover.IMPORTANT: Adjust in small increments to keep fromdamaging the cabinet trim and causing problems with thedoor alignment or top grille fit. To avoid damage to the cabinetor leveling legs, do not apply more than 50 inch-pounds(5.65 Nm) of torque to the leveling bolts. The leveling legs canbe extended to a maximum of 1¹⁄₄" (3.18 cm) below the rollers.4. After leveling the refrigerator, use a straight edge or 4 footlevel going across the front of the refrigerator installation tothe cabinets to check that the refrigerator is still flush.Install Refrigerator and PanelsIMPORTANT: Jenn-Air is not responsible for the removal oraddition of molding or wood overlay panels that would not allowaccess to the refrigerator for service.Install Refrigerator to Adjacent Cabinets1. Open the refrigerator door(s) and freezer drawer. On the hingeside(s), locate the cabinet brackets in the space between thedoor(s) and the refrigerator and the drawer and refrigerator.2. Using the holes in the brackets as a template, predrill ¹⁄₈" deeppilot holes into the adjacent cabinet.3. Using two round head screws (provided with refrigerator) foreach bracket, insert the screws through the cabinet bracketsand into the adjacent cabinetry to anchor the refrigerator.4. Repeat steps 2 and 3 to anchor the other side of therefrigerator to the adjacent cabinetry.Install Cabinet Side TrimsInstall cabinet side trims to hide the brackets fastening therefrigerator to the adjacent cabinets.1. Open the door(s) to a 90° angle.2. With the lip edge of the trim toward the back wall, insert thecabinet side trim between the side of the refrigerator and theadjacent cabinetry.A. Adjacent cabinet or wallB. Installation blockC. Face of refrigeratorA. Rear leveling boltB. Front leveling boltBCA³⁄₄" (1.9 cm)WARNINGTip Over HazardRefrigerator is top heavy and tips easily when notcompletely installed.Keep doors taped closed until refrigerator iscompletely installed.Use two or more people to move and installrefrigerator.Failure to do so can result in death or serious injury.A BABA. Center board¹⁄₄" (6.35 mm) max. above refrigeratorB. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boardsC. Attach to studs with six #8 x 3" (7.6 cm) screwsD. Compressor coverE. Distance from bottom of anti-tip board to floorBAC2" (5 cm)D¹⁄₄" (6 mm)max.84"(213.4 cm)EInstallation Instructions (continued)