Jenn-Air JS42NXFXDW01 Use & Care Manual

Contents

Jenn-Air JS42NXFXDW01 Use & Care Manual Manual pdf 16 page image

Temperature is too warm• New installation? Allow 24 hours following installation for therefrigerator to cool completely.• Door(s) opened often or left open? Allows warm air to enterrefrigerator. Minimize door openings and keep doors fullyclosed.Large load of food added? Allow several hours forrefrigerator to return to normal temperature.Controls set correctly for the surrounding conditions?Adjust the controls a setting colder. Check temperature in24 hours. See "Using the Controls."Refrigerator not cooling? For models with digital controls,turn the refrigerator OFF and then ON to reset. If this does notcorrect the problem, call for service.Air vents blocked? Remove any item from in front of the airvents.There is interior moisture buildupNOTE: Some moisture buildup is normal.• Humid room? Contributes to moisture buildup.• Door(s) opened often or left open? Allows humid air to enterrefrigerator. Minimize door openings and keep doors fullyclosed.=,#'_iI *The ice maker is not producing ice or not enough ice• Refrigerator connected to a water supply and the supplyshutoff valve turned on? Connect refrigerator to watersupply and turn water shutoff valve fully open.Kink in the water source line? A kink in the line can reducewater flow. Straighten the water source line.Ice maker turned on? Make sure wire shutoff arm or switch(depending on model) is in the ON position.New installation? Wait 24 hours after ice maker installationfor ice production to begin. Wait 72 hours for full iceproduction.Large amount of ice recently removed? Allow 24 hours forice maker to produce more ice.Ice cube jammed in the ice maker ejector arm?Remove ice from the ejector arm with a plastic utensil.Reverse osmosis water filtration system connected toyour cold water supply? This can decrease water pressure.See "Water Supply Requirements" in either the InstallationInstruction booklet or the Use & Care Guide.The ice cubes are hollow or smallNOTE: This is an indication of low water pressure.• Water shutoff valve not fully open? Turn the water shutoffvalve fully open.• Kink in the water source line? A kink in the line can reducewater flow. Straighten the water source line.• Reverse osmosis water filtration system connected toyour cold water supply? This can decrease water pressure.See "Water Supply Requirements."• Questions remain regarding water pressure? Call alicensed, qualified plumber.Ice is sticking together in the ice storage bin• It is normal for frost to be on top of the ice storage bin due tonormal opening and closing of the freezer.It is normal for ice to stick together when it is not dispensed orused frequently. It is recommended that the ice storage bin beemptied and cleaned as needed. See "Ice Maker and StorageBin."Off-taste, odor or gray color in the ice• New plumbing connections? New plumbing connectionscan cause discolored or off-flavored ice.Ice stored too long? Discard ice. Wash ice bin. Allow24 hours for ice maker to make new ice.Odor transfer from food? Use airtight, moisture proofpackaging to store food.Are there minerals (such as sulfur) in the water? A waterfilter may need to be installed to remove the minerals.Is there a water filter installed on the refrigerator? Gray ordark discoloration in ice indicates that the water filtrationsystem needs additional flushing.The ice dispenser will not operate properlyFreezer door closed completely? Close the door firmly. If itdoes not close completely, see "The doors will not closecompletely."Ice bin installed correctly? Be sure the ice bin is firmly inposition.New installation? Wait 24 hours after ice maker installationfor ice production to begin. Wait 72 hours for full iceproduction.Ice stuck in the delivery chute? Use a plastic utensil to clearthe delivery chute.Has the wrong ice been added to the bin? Use only cubesproduced by the current ice maker.Has the ice melted around the auger (metal spiral) in theice bin? Empty the ice container. Use warm water to melt theice if necessary.Cut HazardUse a sturdy glass when dispensing ice.Failure to do so can result in cuts.Is the ice dispenser stalling while dispensing "crushed"ice? Change the ice button from "crushed" to "cubed." Ifcubed ice dispenses correctly, depress the button for"crushed" ice and begin dispensing again.Has the dispenser arm been held in too long? Ice will stopdispensing when the arm is held in too long. Wait 3 minutesfor dispenser motor to reset before using again.16