Jet JSMS-10L Operating Instructions Manual

Also see for JSMS-10L: Operating instructions

Contents

Jet JSMS-10L Operating Instructions Manual Manual pdf 4 page image

4Do not lock the moving guard in theopen position. Ensure that themovable guards operate freelywithout jamming.Remove all loose clothing andconfine long hair.Before operating the machine,remove tie, rings, watches, otherjewellery, and roll up sleeves abovethe elbows.Wear safety shoes; never wearleisure shoes or sandals.Always wear the approved workingoutfit:- safety goggles- ear protection- dust protectionDo not wear gloves while operatingthis machine.For the safe handling of saw bladeswear work gloves.Control the stopping time of themachine, it may not be longer than 10seconds.Do NOT stop the blade by forcing themachine or by using sidewayspressure.Insure that the workpiece does notroll when cutting round pieces.Use suitable table extensions andsupporting aids for difficult to handleworkpieces.Never use just your hands forsawingTake care when slotting.Always hold and guide theworkpieces safely during machining.Never cut pieces that are too small.For safety reasons this machinerequires the use of two hands andshould not be operated standing on astaircase or leather.Make sure that the motor ventilationholes are clean and open.Install the machine so that there issufficient space for safe operationand workpiece handling.Keep work area well lighted.The machine is designed to operatein closed rooms and must be placedstable on firm and levelled ground.Make sure that the power cord doesnot impede work and cause people totrip.Keep the floor around the machineclean and free of scrap material, oiland grease.Stay alert!Give your work undivided attention.Use common sense.Keep an ergonomic body position.Maintain a balanced stance at alltimes.Do not operate the machine whenyou are tired.Do not operate the machine underthe influence of drugs, alcohol or anymedication. Be aware that medicationcan change your behaviour.Keep children and visitors a safedistance from the work area.Never reach into the machine while itis operating or running down.Never leave a running machineunattended.Before you leave the workplaceswitch off the machine.Do not operate the electric tool nearinflammable liquids or gases.Normal brushfire might ignite.Observe the fire fighting and fire alertoptions, for example the fireextinguisher operation and place.Do not use the machine in a dumpenvironment and do not expose it torain.Wood dust is explosive and can alsorepresent a risk to health.Dust form some tropical woods inparticular, and from hardwoods likebeach and oak, is classified as acarcinogenic substance.Always use a suitable dust extractiondeviceBefore machining, remove any nailsand other foreign bodies from theworkpiece.Specifications regarding themaximum or minimum size of theworkpiece must be observed.Do not force the power tool. It will doa better and safer job and give youmuch better service if it is used at therate for which it was designed.Do not remove chips and workpieceparts until the machine is at acomplete standstill.Never operate with the guards not inplace – serious risk of injury!Connection and repair work on theelectrical system may be carried outby a qualified electrician onlyAlways unwind any extension cordsfully.Damaged extension cords replaceimmediately.Do not use the power tool if theON/OFF switch does not turn thepower tool ON and OFF.Make all machine adjustments ormaintenance with the machineunplugged from the power source.Select saw blade in relation tomaterial to be cut.Use only sawblades recommendedby manufacturer.Do not use blades made from HighSpeed Steel (HSS).Remove defective saw bladesimmediately.Use carbide-tipped sawblades with anegative chip angle only.Never attempt to use ripping orcombination blades with this saw.When cutting thin walled stock, it isessential that you use a fine toothblade of at least 80 teeth.A coarse blade may hook into thestock and eject it.This machine is not suitable forcutting steel and other metals.Never attempt to cut round orirregular cross-section stock withoutusing a suitable jig.If the blade stalls, switch offimmediately.When using machine on a workstand,always clamp it down.Always listen to the machine andswitch off immediately if abnormalsounds are heard.Keep the slide lock tight unless slideaction is needed.Ensure that the blade guard opensand closes smoothly.Always support long pieces with anadditional supporting stand ofappropriate height.Never carry tool by operating handle.Always use the carry handle or usetwo hands to carry by the base.Always use approved eye and earprotection.Keep hands away from blad at alltimes.Replace table insert when worn.Always unplug machine after use.Do not stare into beam of laserDo not point the laser beam at peopleor animals.Do not use the laser beam on highlyreflective materials. Reflected light isdangerous.