KEB Combivert F5 series Instruction Manual

Also see for COMBIVERT F5 Series: Instruction manual Instructions for use Installation manual Instruction manual Instruction manual

KEB Combivert F5 series Instruction Manual Manual pdf 15 page image

12. Technical Data2.1 Technical Data 230V Class1) With the regulated systems F5-M as well as F5-S 5% must be subtracted as control reserve2) This data is only valid for units with integrated PFC (see "unit identification")3) The wire gauge is based on the maximum fuse rating, copper wire with minimum 75°C insulation rating, THHW or equivalent.If branch circuit protection is selected based on rated input current, the wire size could be reduced.4) This data is only valid for units with internal brake transistor GTR 7 (see "unit identification")5) With units with integrated EMI filter the distance is less:up to max. 5m line length and 4kHz operating frequency = Limit Value B (EN 55011)up to max. 10m line length and 16kHz operating frequency = Limit Value A (EN 55022)7) Rated operation means rated input voltage, rated output current, and rated carrier frequency.8) 8 kHz only with a mounting plate > 55 in² and a 1.6 inch minimum distance to other components.Inverter Size 05 07 09 10 12 13 14Recommended Motor Power [hp] 1/2 1 2 3 5 7.5 10Housing size A A B B D B D D E E GInput RatingsSupply voltage [V] 180...260 ±0 (230 V rated voltage)Supply voltage frequency [Hz] 50 / 60 +/- 2Input phases 1 1 3 1 1 3 1 3 1 3 1 3 1 3 3 3 3Rated input current [A] 4,0 4,0 2,8 8,0 8,0 5,6 14 9,5 14 9,5 19 13 19 13 21 29 36Rated input current 2) [A] – 3,2 – – 6,4 – – – – – –Rated input "real" power 2) [kW] – 0.85 – – 1.5 – – – – – –Recommended maximum input fuse [A] 15 15 15 20 15 20 15 25 20 25 20 25 35 50Recommended wire gauge3) [awg] 14 14 14 12 14 12 14 10 12 10 12 10 10 8Output RatingsRated output power [kVA] 0,9 1.6 2.8 4.0 6.6 9.5 13Rated motor power [kW] 0.37 0.75 1,5 2,2 4.0 5.5 7.5Rated output current [A] 2.0 4.0 6.8 9.6 15.2 22 28Peak current (30 seconds)1) [A] 4,1 7.2 12,6 18 29.7 36 49.5Over current fault (E.OC) trip level [A] 5.0 8.6 15,1 21,6 35.6 43 59Overload curve (see annex) 1Output voltage [V] 3 x 0...V input (3 x 0...255V 2))Output frequency [Hz] Generally 0 to 1600Hz (limited by control board and carrier frequency)Rated switching frequency [kHz] 8 8) 16 8 16 16 8 16 8 8 4 16Maximum switching frequency [kHz] 8 16 8 16 16 16 16 16 16 16 16Power loss at rated operation7) [W] 30 50 55 65 90 130 105 170 210 290 350 330Power loss at rated operation 2) [W] – 85 – – 130 – – – – – –Stall current at 4kHz [A] 2.3 4 7 10 10 16,5 24 33 33Stall current at 8kHz [A] 2.3 4 7 10 10 16,5 24 24 33Stall current at 16kHz [A] – 2.3 – 4 7 8 10 10 16,8 16,8 33Braking CircuitMin. braking resistance 4) [Ohm] 100 56 100 56 47 33 27 16 16 13Typ. braking resistance 4) [Ohm] 180 100 100 68 56 47 22 22 16Max. braking current [A] 4.5 7.5 4.5 7.5 9.5 12 15 25 25 29Installation Information30 100 30 330 330 33030 65 30 165 330 330– 30 – 65 130 330Tightening torque for terminal strip [in lb] 4.5 11EnvironmentalMax. heat sink temperature TOH [°C] 90°C / 194°FStorage temperature [°C] -25...70 °C / -13…158°FOperating temperature [°C] -10...45 °C / 14…113°FHousing design / protection Chassis / IP20Relative humidity max. 95% without condensationApprovalsTested in accordance with… EN 61800-3 /UL508CStandards for emitted interference EN 55011 Class B / EN 55022 Class AStandards for noise immunity IEC 1000-4-2 / -3 / -4 / -5/ -6Climatic category 3K3 in accordance with EN 50178Max. shielded motor cable length at 16kHz5) [ft]B1415Max. shielded motor cable length at 4 kHz 5) [ft]Max. shielded motor cable length at 8 kHz 5) [ft]Technical Data