Kemppi FastMig MXP 37 Pipe Steel Operating Manual

Also see for FastMig MXP 37 Pipe Steel: Operating manual Operating manual

Contents

Kemppi FastMig MXP 37 Pipe Steel Operating Manual Manual pdf 22 page image

ENWORK PACKGroup Material Wire ø (mm) Shielding gas Process NumberAl AlMg5 1.2 Ar Pulse/Double Pulse A02Al AlSi5 1.2 Ar Pulse/Double Pulse A12Fe Fe 1.0 Ar+15–25%CO₂ Pulse/Double Pulse F03Fe Fe 1.2 Ar+15–25%CO₂ Pulse/Double Pulse F04Ss CrNiMo 19 12 1.0 Ar+2%CO₂ Pulse/Double Pulse S06Ss CrNiMo 19 12 1.2 Ar+2%CO₂ Pulse/Double Pulse S04Al AlMg5 1.2 Ar 1-MIG A02Al AlSi5 1.2 Ar 1-MIG A12Fe Fe 0.9 Ar+15–25%CO₂ 1-MIG F02Fe Fe 1.0 Ar+15–25%CO₂ 1-MIG F03Fe Fe 1.2 Ar+15–25%CO₂ 1-MIG F04Fe Fe 0.9 CO₂ 1-MIG F22Fe Fe 1.0 CO₂ 1-MIG F23Fe Fe 1.2 CO₂ 1-MIG F24Fe Fe Metal 1.2 Ar+15–25%CO₂ 1-MIG M04Fe Fe Metal 1.2 CO₂ 1-MIG M24Fe Fe Rutil 1.2 Ar+15–25%CO₂ 1-MIG R04Fe Fe Rutil 1.2 CO₂ 1-MIG R14Ss CrNiMo 19 12 1.0 Ar+2%CO₂ 1-MIG S03Ss CrNiMo 19 12 1.2 Ar+2%CO₂ 1-MIG S04Ss FC-CrNiMo 19 12 1.2 Ar+15–25%CO₂ 1-MIG S84More welding programs are available by purchasing MatchCurve and MatchCustom products.3.5 Arc voltage displayFastMig X is capable of measuring and showing the voltage close to the welding arc. By takingthis feature into use you don't need to be concerned about the voltage losses in weldingcables anymore. With this feature you are only required to set the voltage for the arc beforewelding and after welding you can see the voltage close to the arc.In order to use the arc voltage feature, follow these steps:1. After setting up the welding equipment for the first time, connect the voltage sensingcable to the welding piece and the measurement cable between the wire feeder and thepower source.2. If you are using a sub-feeder, enter the length of the sub-feeder to the SubFeederLengthparameter.3. Set the welding parameters according to your application. Note that the set voltagewhen using 1-MIG, MIG and WiseThin+ welding processes means always the voltage inthe arc despite of ArcVoltage setting.4. Weld with 1-MIG, MIG or with Pulse MIG for at least 5 seconds. During that time thewelding machine calibrates itself for the welding cable length in question. Calibrationvalues are stored into the welding machine, therefore this calibration is required onlyonce after installing the welding machine package.5. If you want to see arc voltage in panels during and after welding, turn the ArcVoltagesetting to ON in X 37 setup panel. Dot after voltage value in XF 37 or XF 38 panel meansthat showed value is arc voltage. In the weld data after welding in X 37 panel 'AVol'means also the arc voltage.6. Voltage sensing cable can be removed after the calibration procedure, but it isrecommended to use it always.NOTE! Steps 1-3 should be repeated every time, when the length of the welding or grounding cableis changed.FastMig MXP 37 Pipe, MXP 3820