Manuals database logo
manualsdatabase
Your AI-powered manual search engine

Kentec Electronics Sigma XT Plus Operation And Maintenance Manual

Also see for Sigma XT Plus: Operation and maintenance manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Page 32 preview
Page 33 preview
Page 34 preview
Page 35 preview
Page 36 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. INTRODUCTION
  4. Static precautions
  5. TECHNICAL SPECIFICATION
  6. FRONT PANEL LAYOUT
  7. SYSTEM DIAGRAMS
  8. CONNECTING TO THE CIRCUIT BOARD
  9. Sounder circuit wiring
  10. Igniting actuator wiring
  11. Connecting to activation inputs
  12. Connecting to Sigma CP fire panel serial bus
  13. Setting up extinguishant monitoring circuit
  14. CONNECTION TO RELAY CONTACTS
  15. BOARDS
  16. Removing status units or ancillary boards
  17. WIRING TO STATUS UNITS AND ANCILLARY BOARD
  18. CONFIGURATION
  19. Reset inhibit time
  20. Extinguishant release time
  21. Delay on manual release
  22. Disable fault output
  23. PANEL OPERATION – ACCESS LEVELS 1 AND 2
  24. Disable Stage 1 output
  25. Select Reserve Solenoid Output (Configuration Option)
  26. Power fault
  27. Watchdog reset
  28. INTERNAL INDICATIONS
  29. MAINTENANCE
  30. COMMISSIONING INSTRUCTIONS
Kentec Electronics Sigma XT Plus Operation And Maintenance Manual Manual pdf 14 page image
Man-1111_SigmaXT+_Coincidence_Unit_18 Page 14 of 368.3 Connecting to activation inputsThe ECU has two monitored activation inputs which can be used for activating the system.Each input must have a 6K8 0.5W end of line resistor fitted (supplied in terminals) and be triggered by a 470R 1Wresistor.Wire volt free contacts from conventional fire panels or addressable modules as show below.EXTINGUISHANTRELEASEPULL DOWN - PUSH BUTTONControlEnable SelectModeActI/ P1ActI/ P2Manrel Hold Mode RelP. SW + - + - + - + -CIE serial Status serial+ -StatuspowerLowpressureAbort470R 1WTRIGGERRESISTOR6K8 0.5WEND OF LINERESISTORACTIVATION INPUT 1 VOLT FREECONTACT FROM ADDRESSABLE MODULEOR CONVENTIONAL FIRE PANEL470R 1WTRIGGERRESISTOR6K8 0.5WEND OF LINERESISTORACTIVATION INPUT 2 VOLT FREECONTACT FROM ADDRESSABLE MODULEOR CONVENTIONAL FIRE PANEL
/ 36
Related manuals for Kentec Electronics Sigma XT Plus
Kentec Electronics XT+ Operating Instructions Manual first page preview
Kentec Electronics XT+ Operating Instructions Manual
Kentec Electronics XT+ Installation Manual first page preview
Kentec Electronics XT+ Installation Manual
Kentec Electronics S792 Information Manual first page preview
Kentec Electronics S792 Information Manual
Kentec Electronics S793 Information Manual first page preview
Kentec Electronics S793 Information Manual
Kentec Electronics 723 Information Manual first page preview
Kentec Electronics 723 Information Manual
Kentec Electronics Syncro Si Product Manual first page preview
Kentec Electronics Syncro Si Product Manual
Kentec Electronics A91000M8 Product Manual first page preview
Kentec Electronics A91000M8 Product Manual
Kentec Electronics Taktis TRC00NC-10 Information Manual first page preview
Kentec Electronics Taktis TRC00NC-10 Information Manual
This manual is suitable for:
Sigma XT Plus
Manuals database logo
manualsdatabase
Your AI-powered manual search engine