Kenwood CD-206 Instruction Manual

Also see for CD-203: Instruction manual Instruction manual Instruction manual Connection guide Connection guide

Kenwood CD-206 Instruction Manual Manual pdf 25 page image

25CD-206/204/203/DPF-R6010/R4010/R3010 (En)÷ Power plug is loosely connected.÷ With the power plug connected to the switchedAC outlet of an amplifier, the power of theamplifier is turned off.÷ Disc is loaded upside down.÷ Disc is loose.÷ Disc is dirty.÷ Disc is cracked.÷ Condensation has occurred on the optical lensunit.÷ Play mode is not entered.÷ The connection cords are inserted loosely.÷ Output level is attenuated too low.÷ Disc is too dirty.÷ Disc is cracked.÷ Oscillation is applied to this unit.÷ This unit is designed so that play begins auto-matically when the unit is turned ON if a disc isalready loaded.The unit is not turned ON with the ON/STANDBY (POWER/ ) switch ON.There is no sound even when a disc is loaded.Music is interrupted. (Sound is skipped.)Play begins as soon as the unit is turned ON.÷ Batteries are exhausted.÷ The remote control unit is too far away from themain system, controlling angle is too large, orthere is an obstacle in between.÷ Replace with new batteries. 8÷ Operate the remote control unit within thecontrollable range. 8In case of difficultyWhat appears to be a malfunction may not always be serious. If your unit should not perform as expected, consult the tablebelow to see if the problem can be corrected before seeking help from your dealer or service representative.Operation to resetThe microcomputer may malfunction (impossibility to operate,erroneous display, etc.) when the connection cords are un-plugged while the unit is ON or due to an external factor. In thiscase, execute the following method to reset the microcomputerand return it to normal condition.CD player unitRemote control unit÷ Please be aware that resetting the CD player will erase all storedinformation and return it to the factory settings.Symptom Cause RemedyUnplug the power cord from the power socket and plug thepower cord into the socket again.÷ Insert the power plug firmly to the AC outlet.÷ Turn the amplifier’s power ON.÷ Load the disc again with its label side up.÷ Insert disc properly.÷ Wipe off the dust on the surface of the discreferring to “Disc handling precautions”.¢÷ Replace the disc with a new one.÷ Remove any condensation from the unit byreferring to the section entitled, “Caution oncondensation”. ¢÷ Press the 6 key.÷ Connect all connection cords firmly.÷ Adjust the output level with OUTPUT key onthe remote control unit. 5÷ Wipe off the dust on the disc surface referringto “Disc handling precautions”. ¢÷ Replace the disc with a new one.÷ Try selecting a place where no strong vibrationsoccur by changing the installation place, etc.÷ If automatic play is not required remove thedisc from the player before setting the unit toSTANDBY mode.KENWOOD CORP. CERTIFIES THIS EQUIPMENTCONFORMS TO DHHS REGULATIONS NO. 21CFR 1040.10, CHAPTER I, SUBCHAPTER J.Location: Back PanelKENWOOD CORPORATION2967-3, ISHIKAWA-CHO, HACHIOJI-SHI,TOKYO, JAPANFor the U.S.A.CAUTION:Use of controls or adjustment or performance of procedures other thanthose specified herein may result in hazardous radiation exposure.In compliance with Federal Regulations, following are reproductions oflabels on, or inside the product relating to laser product safety.Symptom Cause RemedyRemote control operation is not possible.Downloaded From DvDPlayer-Manual.com Kenwood Manuals

/ 28

Related manuals for Kenwood CD-203