Kenwood DV-503 Instruction Manual

Also see for DV-503: Instruction manual Service manual Service manual

Kenwood DV-503 Instruction Manual Manual pdf 40 page image

40KnowledgeDV-402/DVF-3530 (EN/K,P,T,M,X)÷ Load a disc and press the play (3) key.÷ Turn the disc over and properly place it on thedisc tray.÷ Turn on the TV.÷ Properly reconnect the connection cords.÷ This is not a malfunction.÷ Properly connect the audio cords.÷ Set the sound volume to an appropriate level.÷ Press the play (3) key to resume normalplayback mode.÷ Separate this unit as far as possible from thedevice you think is generating the noise.÷ Refer to the “Disc handling precautions” sec-tion and wipe dirt from the disc.÷ Use a new disc.÷ Refer to the “Beware of condensation” sec-tion and evaporate the condensation.÷ Approximately 10 to 20 seconds are requiredfor a disc to start playing, although the timediffers depending on the disc.÷ Properly place the disc on the tray.÷ Refer to the “Video formats” section ,and usea disc with the appropriate video format foryour TV or a TV with the appropriate videoformat for the disc.÷ The subtitle cannot be displayed when theDVD disc being played does not contain therecording of subtitles.÷ Press the SUB TITLE-ON/OFF key to switchon the subtitle mode.÷ The voice (or subtitle) language cannot bechanged when the DVD disc being playeddoes not contain the recording of more thanone voice (or subtitle) language.÷ The viewing angle cannot be changed whenthe DVD disc being played does not containthe recording of more than one angle.÷ More than one viewing angle may be re-corded only in limited sections in a disc.In case of difficultyOperation to resetThe microprocessor may fall into malfunction (impossibility tooperate erroneous display, etc.) when the power cord is unpluggedwhile power is ON or due to an external factor. In this case, executethe following procedure to reset the microprocessor and return it tonormal condition.÷Please note that resetting the microprocessor clears thecontents stored in, it returns the microprocessor to the condi-tion when it left the factory.What appears to be a malfunction may not always be serious. If your unit should not perform as expected, consultthe table below to see if the problem can be corrected before seeking help from your dealer or servicerepresentative.÷ There is no disc in the player.÷ There are no signals recorded on the side of thedisc being played.÷ The TV is not turned on.÷ The connection cords are not properly con-nected.÷ The picture is slightly disrupted during fastforward and fast reverse operations.÷ The audio output cords are not properly con-nected.÷ The volume control of the TV or amplifier is notadjusted properly.÷ The player is in a special playback mode.÷ A nearby device is generating noise.÷ The disc is dirty.÷ The disc is damaged.÷ There is condensation on the optical lens.÷ Time is required for the unit to detect the disctype and size and for the rotation of the motor tostabilize. This is not a malfunction.÷ The disc is not placed horizontally.÷ The video format of the disc being played doesnot match that of the connected TV monitor.÷ The DVD disc being played does not contain therecording of subtitles.÷ The subtitle mode is set to off.÷ The DVD disc being played does not contain therecording of more than one audio (or subtitle)language.÷ The DVD disc being played does not contain therecording of more than one angle.÷ You are attempting to switch the angle in a DVDsection where more than one angle is not re-corded.RemedyCauseDVD player unitSymptomPlayback does not start when the play (3)key is pressed.Playback starts but no image/sound is seen/heard.The picture is disrupted when the image isfast forwarded or fast reversed.No sound is heard.The picture does not look good or the pic-ture/sound quality is poor.It takes a while for the disc to start playing.The tray opens automatically.The top and bottom of the screen cannot beseen.The subtitle is not displayed.The voice (or subtitle) language cannot bechanged.The viewing angle cannot be changed.1 In POWER ON condition, keep the 7 (STOP) key and the ¡¡¡¡¡(Search) key pressed at the same time.2 When both keys are pressed, the region code of the unit, thesoftware version, etc. will be displayed on the display. (Whennothing is done, the display of this information continues.)Example: 71 . 101 . 06:143 Press the ON/OFF key to go to Power OFF.4 When Power ON is performed with the ON/OFF key, thesettings become the default factory settings.