10 | KCA-BT200Before Use• You need to register your cell-phone before usingit with this unit. For more details, see Bluetooth device> (page 12).• If you have registered two or more cell-phones,you need to select one of them. For more details,see Connect> (page 14).• To use the Phone Book, it must be downloaded tothis unit in advance. For details, see the Phone Book> (page 13).• For the method of operation in the Menu mode,refer to the Instruction Manual for Control Unit.• For more information regarding the function with[ ] mark, see (page 23).Making a callDialing Method1. Entry dialing method modeModel-D-1, 2, 3:Press the [ATT] button for at least 1 second.Model-D-4:Select "D.MODE" in Menu mode.2. Select a dialing methodModel-D-1, 4:Press the Control knob ([38] button)."N-DIAL" » "PH-BOOK1" » "PH-BOOK2" » "OUT-CALL"» "IN-CALL"Model-D-2:Press the Control knob ([38])."DIAL" » "INITIAL" » "PHONE BOOK"/ "PH.BOOK" »"OUT-CALL" » "IN-CALL"Model-D-3:2-1-1. Press the [NEXT] button.2-1-2. Press the [1] ("DIAL"), [2] ("PHBK"), [3] ("OUT-C"), or [4] ("IN-C") button.Pressing the [2] ("PHBK") button switchesbetween the Phone Book search methods.3 Methods of operations in the above modes aredescribed below.3. Exit the dialing method selection modeModel-D-1, 2, 3:Press the [ATT] button for at least 1 second.Model-D-4:Exit Menu mode.3 Dial a number ( )2-1. Select the "N-DIAL"/ "DIAL" display.2-2. Enter a phone numberPress the number ([1] – [0]), #([FM]), *([AM]), or+([¢]) button on the remote controller.Basic Operation of hands-free phoning (Model-D)2-3. Make a callPress the [DIRECT] button on the remote controller.☞ You can input max 32 digits.3 Speed dialing (Preset dial)2-1. Select the "N-DIAL"/ "DIAL" display.2-2. Select the preset dial numberModel-D-1, 4:Press the [1] – [6] button.Model-D-2:2-2-1. Press the [FNC] button.2-2-2. Select the number to recall by turning theControl knob.2-2-3. Press the Control knob.Model-D-3:2-2-1. Press the [NEXT] button.2-2-2. Press the [1] ("1") – [6] ("6") button.2-3. Make a callPress the Control knob ([38] button) for at least 1second.☞ You need to register the preset dial number. (page 11)3 Calling a number in the call log ( )2-1. Select the "OUT-CALL"/"OUT-C" (outgoing call) or"IN-CALL"/"IN-C" (incoming call) display.2-2. Select a name or phone numberPush the Control knob towards up or down.2-3. Make a callPress the Control knob ([38] button) for at least 1second.3 Calling a number in the Phone Book ( )2-1. Select the "PH-BOOK1"/ "INITIAL" display, proceedto step 2-2.Select the "PH-BOOK2"/ "PHONE BOOK"/ "PH.BOOK" display, proceed to step 2-3.2-2. Select the initial to be searched forOperation type OperationMove to the nextcharacter.Push the Control knob towards right or left.Move to the next row. Push the Control knob towards up or down.Determine theselected initialPress the Control knob ([38] button) for atleast 1 second.2-3. Select the nameOperation type OperationChange the name. Push the Control knob towards up or down.Change the initial. Push the Control knob towards right or left.2-4. Make a callPress the Control knob ([38] button) for at least 1second.
