Kenwood KDC-BT34U Instruction Manual

Contents

Kenwood KDC-BT34U Instruction Manual Manual pdf 15 page image

13ENGLISH |AUDIO SETTINGSWhile listening to any source...1 Press the volume knob to enter [FUNCTION].2 Turn the volume knob to select [AUDIO CONTROL], then press theknob.3 Turn the volume knob to make a selection (see the following table),then press the knob.Repeat step 3 until the desired item is selected or activated.4 Press and hold to exit.To return to the previous setting item or hierarchy, press .Default: XXSUB-W LEVEL –15 to +15 (0): Adjusts the subwoofer output level.BASS LEVEL –8 to +8 (+6): Adjusts the level to memorize for each source. (Beforemaking an adjustment, select the source you want toadjust.)MID LEVEL –8 to +8 (+5):TRE LEVEL –8 to +8 (0):EQ PROBASS ADJUST BASS CTR FRQ 60/ 80/ 100/ 200: Selects the center frequency.BASS LEVEL –8 to +8 (+6): Adjusts the level.BASS Q FACTOR 1.00/ 1.25/ 1.50/ 2.00: Adjusts the quality factor.BASS EXTEND ON: Turns on the extended bass. ; OFF: Cancels.MID ADJUST MID CTR FRQ 0.5/ 1.0/ 1.5/ 2.5K: Selects the center frequency.MID LEVEL –8 to +8 (+5): Adjusts the level.MID Q FACTOR 0.75/ 1.00/ 1.25: Adjusts the quality factor.TRE ADJUST TRE CTR FRQ 10.0/ 12.5/ 15.0/ 17.5K: Selects the center frequency.TRE LEVEL –8 to +8 (0): Adjusts the level.PRESET EQ DRIVE EQ/ TOP40/ POWERFUL/ ROCK/ POPS/ EASY/ JAZZ/NATURAL/ USER: Selects a preset equalizer suitable to the musicgenre. (Select [USER] to use the customized bass, middle, and treblesettings.)[DRIVE EQ] is a preset equalizer that reduces noise from the road.BASS BOOST LV1/ LV2/ LV3: Selects your preferred bass boost level. ; OFF: Cancels.LOUDNESS LV1/ LV2: Selects your preferred low and high frequencies boost toproduce a well-balanced sound at a low volume level. ; OFF: Cancels.SUBWOOFER SET ON: Turns on the subwoofer output. ; OFF: Cancels.LPF SUBWOOFER THROUGH: All signals are sent to the subwoofer. ; 85HZ/ 120HZ/160HZ: Audio signals with frequencies lower than 85 Hz/ 120 Hz/160 Hz are sent to the subwoofer.SUB-W PHASE REVERSE (180°)/ NORMAL (0°): Selects the phase of the subwooferoutput to be in line with the speaker output for optimum performance.(Selectable only if a setting other than [THROUGH] is selected for[LPF SUBWOOFER].)FADER R15 to F15 (0): Adjusts the rear and front speaker output balance.BALANCE L15 to R15 (0): Adjusts the left and right speaker output balance.VOLUME OFFSET(Default: 0)–8 to +8 (for AUX) ; –8 to 0 (for other sources): Presets the volumeadjustment level of each source. (Before adjustment, select the sourceyou want to adjust.)SOUND RECNSTR(Soundreconstruction)ON: Creates realistic sound by compensating the high-frequencycomponents and restoring the rise-time of the waveform that are lostin audio data compression. ; OFF: Cancels.• [SUB-W LEVEL]/ [SUBWOOFER SET]/ [LPF SUBWOOFER]/ [SUB-W PHASE] isselectable only if [SWITCH PREOUT] is set to [SUB-W]. ( 4)• [SUB-W LEVEL]/ [LPF SUBWOOFER]/ [SUB-W PHASE] is selectable only if[SUBWOOFER SET] is set to [ON].