Kenwood KDC-X305 Instruction Manual

Also see for KDC-BT35: Quick start guide

24 ENGLISH[SOUND EFFECT][SOUND RECNSTR](Soundreconstruction)(Not applicable for RADIO source, AUX source and SIRIUS XM source.)[ON]: Creates realistic sound by compensating the high-frequencycomponents and restoring the rise-time of the waveform that are lost inaudio data compression. ; [OFF]: Cancels.[SPACE ENHANCE] (Not applicable for RADIO source.)[SML]/[MED]/[LRG]: Virtually enhances the sound space. ;[OFF]: Cancels.[SND REALIZER] [LV1]/[LV2]/[LV3]: Virtually makes the sound more realistic. ;[OFF]: Cancels.[STAGE EQ] [LOW]/[MID]/[HI]: Virtually adjusts the sound position heard from thespeakers. ; [OFF]: Cancels.[DRIVE EQ] [ON]: Boosts the frequency to reduce the noise heard from outside thecar or running noise of the tyres. ; [OFF]: Cancels.[SPEAKER SIZE] The frequency and slope settings are automatically set for the crossoverof the selected speaker.[FRONT] [SIZE] [3.5”]/[4”]/[4.75”]/[5”]/[6.5”]/[6.75”]/[7”]/[4×6]/[5×7]/[6×8]/[6×9]/[7×10]: Selects according to theconnected speaker size for optimum performance.[TWEETER] [SMALL]/[MIDDLE]/[LARGE]: Selects according tothe size range of the connected tweeter for optimumperformance. ; [NONE]: Not connected.[REAR] [3.5”]/[4”]/[4.75”]/[5”]/[6.5”]/[6.75”]/[7”]/[4×6]/[5×7]/[6×8]/[6×9]/[7×10]: Selects according to the connected speaker size foroptimum performance. ; [NONE]: Not connected.[SUBWOOFER] [6.5”]/[8”]/[10”]/[12”]/[15” OVER]: Selects according to theconnected speaker size for optimum performance. ; [NONE]: Notconnected.Audio Settings[X ‘ OVER][TWEETER] [FRQ] [1KHZ]/[1.6KHZ]/[2.5KHZ]/[4KHZ]/[5KHZ]/[6.3KHZ]/[8KHZ]/[10KHZ]/[12.5KHZ]: Adjusts thecrossover frequency for the tweeter speaker.[GAIN LEFT] [–8] to [0]: Adjusts the output volume of the lefttweeter.[GAIN RIGHT] [–8] to [0]: Adjusts the output volume of the righttweeter.[FRONT HPF] [F-HPF FRQ] [30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/[90HZ]/[100HZ]/[120HZ]/[150HZ]/[180HZ]/[220HZ]/[250HZ]: Adjusts the crossover frequencyfor the selected speakers (high pass filter). ;[THROUGH]: All signals are sent to the selectedspeakers.[F-HPF SLOPE] [–6DB]/[–12DB]/[–18DB]/[–24DB]: Adjusts thecrossover slope.(Selectable only if a setting other than [THROUGH] isselected for [F - HPF FRQ].)[F-HPF GAIN] [–8] to [0]: Adjusts the output volume of theselected speaker.[REAR HPF] [R-HPF FRQ]Configure the settings for the rear speakers similarlyto the front speakers.[R-HPF SLOPE][R-HPF GAIN][SUBWOOFER LPF] [SW LPF FRQ] [30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/[90HZ]/[100HZ]/[120HZ]/[150HZ]/[180HZ]/[220HZ]/[250HZ]: Adjusts the crossover frequencyfor the subwoofer (low pass filter). ; [THROUGH]: Allsignals are sent to the subwoofer.