Kenwood KDC-X879 Instruction Manual

Also see for KDC-MP925: Service manual Instruction manual

Contents

English | 291st sectionMulti-function key operation Audio setup Item[2]"X’Over"[2] "FRONT"[3] "REAR"[4] "CNTR"[5] "SW"[5] "PHASE"High Pass Filter FrontHigh Pass Filter RearHigh Pass Filter CenterLow Pass Filter SubwooferSubwoofer Phase setting[3]"DTA"[2] "FRONT"[3] "REAR"[4] "CNTR"[5] "SW"DTA FrontDTA RearDTA CenterDTA Subwoofer[4]"EQ"[2] "FRONT"[3] "REAR"[4] "CNTR"[2] "BASS"*[3] "MID"*[4] "TRE"*[2] "BASS"*[3] "MID"*[4] "TRE"*[2] "BASS"*[3] "MID"*[4] "TRE"*EQ Front Bass settingEQ Front Middle settingEQ Front Treble settingEQ Rear Bass settingEQ Rear Middle settingEQ Rear Treble settingEQ Center Bass settingEQ Center Middle settingEQ Center Treble setting[5]"SP-LEV"*2[2] "FRONT"[3] "REAR"[4] "CT/SW"[5] "T-TONE"[2] "Front-L"[2] "Front-R"[3] "Rear-L"[3] "Rear-R"[4] "Center "[4] "Sub Woofer"SP-LEV Front LeftSP-LEV Front RightSP-LEV Rear LeftSP-LEV Rear RightSP-LEV CenterSP-LEV SubwooferSP-LEV Test tone• * The followings can be adjusted each time button [2]"BASS", button [3] "MID" or button [4] "TRE" of "EQ"functions is pressed.[2]"BASS" "BASS F" (Bass Center Frequency)"BASS L" (Bass Level)"BASS Q" (Bass Q Factor)[3]"MID" "MID F" (Middle Center Frequency)"MID L" (Middle Level)"MID Q" (Middle Q Factor)[4]"TRE" "TRE F" (Treble Center Frequency)"TRE L" (Treble Level)"TRE Q" (Treble Q Factor)• *2 You can listen to the "T-TONE" when you havetuned it. The sound level is reduced when "T-TONE"is selected. The sound returns to the normal levelwhen the original source is selected.• X'over (Crossover Network Setup)You can manually set a crossover frequency ofspeakers.• DTA (Digital Time Alignment)Manually set the sound output timing of eachchannel.• EQ (Equalizer)You can manually set the equalizer curve.• SP-LEV (Speaker Level)Set the volume at each setup position.2nd sectionMulti-function key operation Audio setup item[2]"MEMORY"[2] "USER"[3] "INST"User MemoryUser Insttaller[3]"CALL"[2] "USER"[3] "INST"Call UserCall Insttaller• You can store an adjusted audio setup value byselecting "MEMORY". Also, you can recall it byselecting "CALL". Refer to 'Audio Setup memory Recall'(page 30).3 Adjust the Audio setup itemPress the [4] or [¢] button.Each time the button is pressed the settingswitches as shown below.Adjustment Item RangeHigh Pass Filter FrontHigh Pass Filter RearHigh Pass Filter CenterThrough/30 — 250 (Hz)Low Pass Filter Subwoofer 30 — 250 (Hz)Subwoofer Phase setting Normal/ ReverseDTA Front/DTA Rear/DTA Subwoofer0 — 20.33 (feet)DTA Center 0 — 5.67 (feet)Bass Center Frequency 60 — 400 (Hz)Middle Center Frequency 500 (Hz) — 3.15 (KHz)Treble Center Frequency 4.00 (kHz) — 16.00 (KHz)Bass Level/ Middle Level/Treble Level-9 — +9 dBBass Q Factor/ Middle Q Factor/Treble Q Factor0.25/ 0.50/ 1.00/ 2.00SP-LEV Front Left/SP-LEV Front RightSP-LEV Rear Left/SP-LEV Rear RightSP-LEV Center/SP-LEV Subwoofer-10 — +10• The Adjustment item can also be controlled by therotary volume knob. Refer to 'Rotary Volume knoboperation mode select' (page 14).• To get the best sound, first set the "CABIN" and "SP-SEL" parameters using the 'Audio Setup (Easy mode)'(page 28). Refer to 'Notes on Sound ManagementSystem' (page 12).• When the 'Dual Zone System' (page 25) is ON, each ofthe following setup is ignored.- "X'over"/ "EQ" / "DTA"4 Exit Audio setup modePress the [6] ("RTN") button.