Kenwood KR-V999D Instruction Manual

Contents

Preparations1 2KR-V999D (En/T)Operations OtherConnecting the system controlConnecting system control cords after connecting a KENWOOD audio component system lets you take advantage ofconvenient system control operations.There are two KENWOOD system control modes. Make connections according to the groups of terminal symbols shownbelow.ƒ Mode : lets you combine f, ƒ, and F terminalsMode : for terminals onlyThis unit is compatible with both [XS8] and [SL16] modes. It comes from the factory set to the [SL16] mode. To switch to the [XS8] mode, followthe instructions in “SWITCHING FROM [SL16] TO [XS8]” below.[SL16] [XS8][SL16][SL16] [XS] [XS8] [XR][SL16] [XS] [XS8][XS][SL16] [XS8][SL16][SL16] [XS] [XS8] [XR][SL16] [XS] [XS8][XS]SYSTEMCONTROLcordSYSTEMCONTROLcordEXAMPLE: [XS8] mode connectionsThe underlined portion represents the setting of the system control mode.EXAMPLE: [SL16] mode connectionsThe underlined portion represents the setting of the system control mode.ReceiverMD recorderCassette deckCD playerRecord playerReceiverMD recorderCassette deckCD playerRecord playerSYSTEM CONTROL OPERATIONSRemote ControlLets you operate this unit with the system remote supplied with thereceiver.Automatic Operation (except [XR] equipment)When you start playback from a source component, the input selectoron this unit switches to that component automatically.Synchronized Recording (except [XR] equipment)Lets you synchronize recording with the start of playback whenrecording from CD, MD or analog discs.SWITCHING FROM [SL16] TO [XS8]You can easily change the system control mode by adjusting theposition of the SYSTEM CONTROL switch on the rear panel.Do this operation after completing all connections.1. [SL16] equipment cannot be combined with [XR], [XS], and [XS8] equipment for system operations. If yourequipment consists of this kind of combination, please do not connect any system control cords. Even withoutsystem control cords, normal operations can be carried out without effecting performance.2. Do not connect system control cords to any components other than those specified by KENWOOD. It maycause a malfunction and damage your equipment.3. Be sure the system control plugs are inserted all the way in to the system control terminals.Setting up the systemRegistering setup codes for KENWOOD audio components• Once you finish making the system connections, be sure to register the appropriate setup code for each component. ‚• If you own remote controllable KENWOOD audio components that are not compatible with system control (or cannot be combined with your othersystem control components), registering the setup code enables you to control those components using the remote control supplied with thisunit (without connecting system control cords). To register setup codes for your remote controllable KENWOOD audio components, see"Registering setup codes for other components". ‚• In order to take advantage of the system control operations, the components must be connected to the correct jacks. To use a CD player it mustbe connected to the CD jacks. To use a cassette deck (or MD recorder) it must be connected to the TAPE1/MD jacks. When using more than oneCD player (etc.) only the one connected to the specified jacks may be connected for system control.• Some CD players and cassette decks are not compatible with the [SL16] system control mode. Be sure to use the [XS8] system control modewhen making system connections with equipment that is not [SL16] compatible.• Some MD players are not system control compatible. You cannot make system control connections to this kind of equipment.NotesNotesSL 16XS 8For [SL16]For [XS8]• This operation will not effect items stored in the memory.• After switching the system control mode, turn the power off andthen on once to confirm the new setting.