Kenwood KVT-915DVD Instruction Manual

Also see for KVT-915DVD: Service manual Service manual Instruction manual

Contents

English 111110 EnglishEnglishTroubleshooting GuideThe viewing angle cannot be changed.• The DVD disc being played does not contain therecording of more than one angle.• You are attempting to switch the angle in a DVDsection where more than one angle is not recorded.Playback will not start even after a title is selected.• A viewing restriction (RATING) has been set for thedisc.The voice or subtitle language selected in the initial setting is not played.• The DVD disc being played does not contain therecording of the selected voice or subtitle language.Disc sourceThe disc control mode cannot be selected.• No wire has been connected to the disc changerinput terminal on the unit.The specified disc does not play, but another one plays instead.• The specified CD is quite dirty.• The CD is upside-down.• The disc is loaded in a different slot from thatspecified.• The disc is severely scratched.The sound skips.• Something is touching the disc changer.• The CD is scratched or dirty.The display shows that the changer is being played, but no sound can be heard.• The computer chip in the unit is not functioningnormally.The specified track will not play.• Random play or magazine random play has beenselected.Track repeat, disc repeat, track scan, disc scan, random play, and magazine random play start by themselves.• The setting is not cancelled.Can’t remove disc.• The cause is that more than 10 minutes has elapsedsince the vehicle ACC switch was turned OFF.MP3/WMA sourceCannot play an MP3/WMA.• The media is scratched or dirty.The sound skips when an MP3/WMA is being played.• The media is scratched or dirty.• The recording condition is bad.The MP3/WMA track time isn’t displayed correctly.• ---Can’t display the ID3 tag information correctly.• Record is not made in conformity with the ID3 tagversion 1.x.The following messages are displayed when certain problems are occurring in your system. Takethe recommended actions.Hot Error The protective circuit in the unit activates when the temperature inside the unit exceeds 60°C(140°F), stopping all operation.] Cool down the unit by opening the windows or turning on the air conditioner. As thetemperature falls below 60°C (140°F), the disc will start playing again.Hold Error The protective circuit in the unit activates when the temperature inside the automatic discchanger exceeds 60°C (140°F), stopping all operation.] Cool down the unit by opening the windows or turning on the air conditioner. As thetemperature falls below 60°C (140°F), the disc will start playing again.Mecha Error The disc player is malfunctioning.] Eject the disc and try inserting it again. Contact the Kenwood dealer if this indicator continuesblinking or the disc cannot be ejected.Disc Error The unplayable discs is inserted.Read Error The disc is upside-down.] Load the disc with the labeled side up.The disc is quite dirty.] Clean the disc, referring to the section on (see page 6).Region code Error The DVD software encoded for other region code.Parental level Error The parental level is set to high levels.Error 07 — 67 The unit is malfunctioning for some reason.] Press the reset button on the unit. If the "Error ##" code does not disappear, consult yournearest service center.• The viewing angle cannot be changed when the DVD discbeing played does not contain the recording of more thanone angle.• More than one viewing angle may be recorded only inlimited sections in a disc.• Check the viewing restriction level (RATING) setting.• Use a DVD disc containing the recording of the selectedvoice or subtitle language.• Connect the wire to the disc changer input terminal on theunit.• Clean the CD.• Load the CD with the labeled side up.• Eject the disc magazine and check the number for thespecified disc.• Try another disc instead.• Remove whatever is touching it.• If skipping happens at the same place when the car isstopped, something with the CD is wrong. Clean the CD.• Press the reset button on the unit (see page 4).• Turn off random play or magazine random play.• The settings for these functions remain on until thesetting to off or the disc ejected, even if the power isturned off or the source changed.• The disc can only be removed within 10 minutes of theACC switch being turned OFF. If more than 10 minuteshas elapsed, turn the ACC switch ON again and press theEject button.• Clean the media, referring to the CD cleaning of thesection on (see page 6).• Clean the media, referring to the CD cleaning of thesection on (see page 6).• Record the media again or use another media.• There are times when it isn’t displayed correctly accordingto the MP3/WMA recording conditions.• Record in conformity with the ID3 tag version 1.x.Also, the display may be incorrect if an MP3 file uses theID3 tag v1.x standard and if this standard has beenexpanded after production of the machine software.

/ 57

Related manuals for Kenwood KVT-915DVD