Kenwood NEXEDGE NXR-710 Instruction Manual

Also see for NEXEDGE NXR-710: Instruction manual Instruction manual Service manual Instruction manual Instruction manual

1◆ Government law prohibits the operation of unlicensed radiotransmitters within the territories under government control.◆ Illegal operation is punishable by fine and/or imprisonment.◆ Refer service to qualified technicians only.◆ This repeater is intended for use as a fixed base station withthe antenna located outdoors on the rooftop or on an antennatower.◆ This repeater is designed for a 13.2 V DC power source!Never use a 24 V DC or higher source to power the repeater.◆ Use only the supplied DC cord.◆ Do not remove the ferrite core attached to the DC cord. Doingso may cause interference with radio communications.THANK YOU!We are grateful you purchased this KENWOOD repeater. Webelieve this easy-to-program repeater will be highly effective inyour communications system, and will keep personnel operatingat peak efficiency.PRECAUTIONS• Do not expose the unit to rain or moisture; to prevent fire orelectric shock.• Do not open the unit under any circumstances; to avoid riskof electric shock.• Do not expose the unit to long periods of direct sunlight, norplace it close to heating appliances.• Do not place the unit in excessively dusty and/or humidareas, nor on unstable surfaces.• If you detect an abnormal odor or smoke coming from theunit, disconnect the power from the unit immediately. Contactyour KENWOOD service center or dealer.NOTICES TO THE USERUNPACKING AND CHECKING EQUIPMENTNote: The following unpacking information is for use by yourKENWOOD dealer, an authorized KENWOOD service center, or thefactory.Carefully unpack the repeater. We recommend that you identifythe items listed in the following table before discarding thepacking material. If any items are missing or have been damagedduring shipment, file a claim with the carrier immediately.Item Part Number QuantityHardware fixture J21-8559-XX 1Front glass B10-2635-XX 1Name plates B11-1259-XX 1Cushion G13-1801-XX 4Cushion G13-1802-XX 4Foot J02-0475-XX 2Foot J02-0492-XX 2Grommet J59-0302-XX 2Handle K01-0418-XX 1Screws N30-4006-XX 2Screws N35-3006-XX 5DC cord E30-3427-XX 1Lead wire with connector (15 pin) E31-3228-XX 1Fuse F05-1537-XX 1Instruction Manual B62-2200-XX 1INSTALLATIONTo install the handles onto the front panel of the repeater, alignthe handles with the holes on the front panel, then secure thehandles using the supplied screws.Please consult your dealer for installing the repeater andantenna.MICROPHONEConnect an optional KMC-30, KMC-35, KMC-27A, KMC-27B,KMC-9C, or KMC-53 KENWOOD microphone to the MIC jack onthe front panel.NOTIFICATIONThis equipment complies with the essential requirements of Directive2014/53/EU.RESTRICTIONSThis equipment requires a licence and is intended for use in thecountries as below.AT BE DK FI FR DE GR IS IEIT LI LU NL NO PT ES SE CHGB CY CZ EE HU LV LT MT PLSK SI BG RO HR TRISO3166B62-2200-60 (E)VHF DIGITAL BASE-REPEATER/ UHF DIGITAL BASE-REPEATERINSTRUCTION MANUALNXR-710/ NXR-810Information on Disposal of Old Electrical and Electronic Equipment and Batteries(applicable for countries that have adopted separate waste collection systems)Products and batteries with the symbol (crossed-out wheeled bin)cannot be disposed as household waste.Old electrical and electronic equipment and batteries should berecycled at a facility capable of handling these items and their wastebyproducts.Contact your local authority for details in locating a recycle facilitynearest to you.Proper recycling and waste disposal will help conserve resourceswhilst preventing detrimental effects on our health and the environment.© 2019The AMBE+2TM voice coding Technology embodied in this productis protected by intellectual property rights including patent rights,copyrights and trade secrets of Digital Voice Systems, Inc. Thisvoice coding Technology is licensed solely for use within thisCommunications Equipment. The user of this Technology is explicitlyprohibited from attempting to extract, remove, decompile, reverseengineer, or disassemble the Object Code, or in any other wayconvert the Object Code into a human-readable form. U.S. PatentNos. #8,315,860, #8,595,002, #6,912,495, #8,200,497, #7,970,606,and #8,359,197.Model Frequency range Max. output powerNXR-710-E TX/RX 136.000 - 174.000 MHz 50 WNXR-810-E TX/RX 400.000 - 470.000 MHz 40 WFirmware CopyrightsThe title to and ownership of copyrights for firmware embedded in KENWOODproduct memories are reserved for JVCKENWOOD Corporation.