Kenwood Nexedge NXR-810 Instruction Manual

Also see for NEXEDGE NXR-710: Instruction manual Service manual Instruction manual Instruction manual Instruction manual

Contents

front panel

◆ Government law prohibits the operation of unlicensed radiotransmitters within the territories under government control.◆ Illegal operation is punishable by fine and/or imprisonment.◆ Refer service to qualified technicians only.◆ This repeater is intended for use as a fixed base station withthe antenna located outdoors on the rooftop or on an antennatower.◆ This repeater is designed for a 13.2 V DC power source!Never use a 24 V DC or higher source to power the repeater.◆ Use only the supplied DC cord.◆ Do not remove the ferrite core attached to the DC cord. Doingso may cause interference with radio communications.THANK YOU!We are grateful you purchased this Kenwood repeater. Webelieve this easy-to-program repeater will be highly effective inyour communications system, and will keep personnel operatingat peak efficiency.PRECAUTIONS• Do not expose the unit to rain or moisture; to prevent fire orelectric shock.• Do not open the unit under any circumstances; to avoid riskof electric shock.• Do not expose the unit to long periods of direct sunlight, norplace it close to heating appliances.• Do not place the unit in excessively dusty and/or humidareas, nor on unstable surfaces.• If you detect an abnormal odor or smoke coming from theunit, disconnect the power from the unit immediately. Contactyour Kenwood service center or dealer.NOTICES TO THE USERThe AMBE+2 TM voice coding Technology embodied in this productis protected by intellectual property rights including patent rights,copyrights and trade secrets of Digital Voice Systems, Inc. This voicecoding Technology is licensed solely for use within this CommunicationsEquipment. The user of this Technology is explicitly prohibited fromattempting to extract, remove, decompile, reverse engineer, ordisassemble the Object Code, or in any other way convert the ObjectCode into a human-readable form. U.S. Patent Nos. #5,870,405,#5,826,222, #5,754,974, #5,701,390, #5,715,365, #5,649,050,#5,630,011, #5,581,656, #5,517,511, #5,491,772, #5,247,579, #5,226,084and #5,195,166.Firmware CopyrightsThe title to and ownership of copyrights for firmware embedded inKenwood product memories are reserved for Kenwood Corporation.UNPACKING AND CHECKING EQUIPMENTNote: The following unpacking information is for use by your Kenwooddealer, an authorized Kenwood service center, or the factory.Carefully unpack the repeater. We recommend that you identifythe items listed in the following table before discarding thepacking material. If any items are missing or have been damagedduring shipment, file a claim with the carrier immediately.Item Part Number QuantityHardware fixture J21-8559-XX 1Front glass B10-2635-XX 1Name plates B11-1259-XX 1Cushion G13-1801-XX 4Cushion G13-1802-XX 4Foot J02-0475-XX 2Foot J02-0492-XX 2Grommet J59-0302-XX 2Handle K01-0418-XX 1Screws N30-4006-XX 2Screws N35-3006-XX 5DC cord E30-3427-XX 1Lead wire with connector (15 pin) E31-3228-XX 1Fuse F05-1537-XX 1Instruction Manual B62-2200-XX 1INSTALLATIONTo install the handles onto the front panel of the repeater, alignthe handles with the holes on the front panel, then secure thehandles using the supplied screws.Please consult your dealer for installing the repeater andantenna.MICROPHONEConnect an optional KMC-30, KMC-35, KMC-27A, KMC-27B,or KMC-9C Kenwood microphone to the MIC jack on the frontpanel.NOTIFICATIONThis equipment complies with the essential requirements of Directive1999/5/EC.The use of the warning symbol means the equipment is subject torestrictions of use in certain countries.This equipment requires a licence and is intended for use in thecountries as below.AT BE DK FI FR DE GR ISIE IT LI LU NL NO PT ESSE CH GB CY CZ EE HU LVLT MT PL SK SI BG ROISO3166© B62-2200-00 (E)09 08 07 06 05 04 03 02 01 00VHF DIGITAL BASE-REPEATER/ UHF DIGITAL BASE-REPEATERINSTRUCTION MANUALNXR-710/ NXR-810Information on Disposal of Old Electrical and Electronic Equipment andBatteries (applicable for EU countries that have adopted separate wastecollection systems)Products and batteries with the symbol (crossed-out wheeled bin) cannotbe disposed as household waste.Old electrical and electronic equipment and batteries should be recycled ata facility capable of handling these items and their waste byproducts.Contact your local authority for details in locating a recycle facility nearestto you.Proper recycling and waste disposal will help conserve resources whilstpreventing detrimental effects on our health and the environment.Notice: The sign "Pb" below the symbol for batteries indicates that thisbattery contains lead.