TK-23178REALIGNMENT / 模式组合4. Wireless Clone Mode4-1. Outline“Wireless Clone Mode” copies the transceiver data to an-other transceiver.The dealer can copy the transceiver data to anothertransceiver even without the use of a personal computer.4-2. ExampleThe transceiver can copy the programming data to one ormore transceivers via RF communication.The clone source and clone target/s must be in wirelessclone mode.4-3. Operation1. To switch the clone target/s to Wireless Clone mode,press and hold the [power ON.2. Wait for 2 seconds. “CLONE” appears on the LCD, fol-lowed by “FRQTBL 1”.3. Select a channel table number using the [Selector] knob.4. To switch the clone source to Wireless Clone mode,press and hold the [power ON.5. Wait for 2 seconds. “CLONE” appears on the LCD, fol-lowed by “FRQTBL 1”.6. Select the same channel table number as the clone tar-get/s.7. Press the [S] key on the clone master to begin data trans-mission. When the clone target starts to receive data, thegreen LED will light and “CLONING” will appear on theLCD. The source unit will display “MASTER”.8. When the clone source fi nishes sending data, a “confi r-mation” tone will sound and “COMPLETE” will appear onthe LCD. If data transmission failed while cloning, the tar-get unit will produced an error tone and “CLONE NG” willappear on the LCD.9. If the cloning fails, no data will be available in the targetunit when it is returned to User mode.10.When the cloning is successful, the target unit's “Scan”and “Key lock” functions will return to their default values(Scan = OFF, Key lock = OFF).11.The source will remain in clone mode after cloning. Thetarget unit will return to user mode after a successfulcloning.Note:• The dealer can clone data to two or more transceivers byrepeating the above procedures.• If the transceivers wireless clone Mode is configured as“Disabled”, the transceiver cannot enter Clone mode.• The table shown below will cover the frequency tablesused for wireless cloning.• Wireless clone mode cannot be entered in battery lowstate.• A unit cannot be a “Source Unit” if it is unprogrammed. Ifthe [S] key is pressed, an “error” tone will sound.• Once a unit is set to be the source, it cannot be a targetafter the data has been transmitted. This protects thedata in the source unit.• MSK signaling is used in cloning.4. 无线复制模式4-1. 概要“无线复制模式”可以将一台手持对讲机的数据复制到其它的手持对讲机。经销商甚至不使用个人电脑也可以将一台手持对讲机的数据复制到其它的手持对讲机。4-2. 例手持对讲机可以通过 RF 通信复制编程数据到一台或更多的手持对讲机。复制主机和复制子机必须处于无线复制模式。4-3. 操作方法1. 将子机切换到无线复制模式,接通 (ON) 手持对讲机电源开关的同时,持续按 [2. 等待 2 秒。LCD 上显示“CLONE”,然后显示“FRQTBL 1”。3. 用 [ 选择器 ] 旋钮选择频率表号码。4. 将主机切换到无线复制模式,打开手持对讲机电源 (ON)的同时,持续按 [5. 等待 2 秒。在 LCD 上显示“CLONE”,然后显示“FRQTBL 1”。6. 选择与复制子机相同的频率表号码。7. 按复制主机上的 [S] 键,开始传输数据。当复制子机开接收数据时,绿色 LED 将亮灯,并且“CLONING”显示在 LCD 上。主机将显示出“MASTER”。8. 当复制主机完成数据传送,将发出一个“确认”音,并且在 LCD 上显示出“COMPLETE”。如果复制中数据通讯失败,子机将发出错误音,而且在 LCD 上显示出“CLONE NG”。9. 如果复制失败,子机回到用户模式时会无可用数据。10. 当复制成功时,子机的“扫描”和“键锁定”功能将返回到它们的初始值 ( 扫描= OFF,键锁定= OFF)。11. 主机在复制后将停留在复制模式。复制成功后,子机将返回到用户模式。注∶• 经销上可以把同样的数据反复地复制到两台或更多的手持对讲机。• 如果手持对讲机的无复制模式被设定为“禁用”,则手持对讲机不能进入复制模式。• 此表是使用于无线复制的频率表。• 在电池低电压状态时,不能进入无复制模式。• 如果没有被编程,就不能成为“主机”。如果 [S] 键被按,将会发出“错误”音。• 手持对讲机一旦被设定为主机,而且数据被传送之后,它就不能成为子机。此功能是为了保护主机内的数据。• MSK 信号用于复制。• 电子干扰有可能导致无线复制时数据传送失败,如在工作台上受到电波或电磁的干扰。