Kenwood VR-50RS Instruction Manual

17 ENIf you have selected “NML” as the Front speakers setting,1 CNTR NML (normal) : An average size Center speaker isconnected to this model.2 CNTR OFF : Center speaker setting mode to thismodel is OFF.9 Press the SETUP key again to accept the setting.•The surround speaker setting indication “SURR NML” appears.0 Use the MULTI CONTROL knob or MULTI CONTROL %/fi keysto select the appropriate Surround speaker setting.If you have selected “LRG” as the Center speaker setting,1 SURR NML (normal) : Average size Surround speakers areconnected to this model.2 SURR LRG (large) : Large Surround speakers are connectedto this model.3 SURR OFF : Surround speaker setting mode to thismodel is OFF.If you have selected other than “LRG” as the Center speakersetting,1 SURR NML (normal): Average size Surround speakers areconnected to this model.2 SURR OFF : Surround speaker setting mode to thismodel is OFF.• When the setting “SURR OFF” is selected, the procedure skipsto step #.! Press the SETUP key to accept the setting.• The Surround Back speaker setting indication “BS” appears.@ Use the MULTI CONTROL knob or MULTI CONTROL %/fi keysto select the appropriate Surround Back speaker setting.If you have selected “LRG” as the surround speaker setting,1 BS NML (normal : Average size Surround back speakers areconnected to this model.2 BS LRG (large) : Large Surround Back speaker isconnected to this model.3 BS OFF : Surround Back speaker setting mode tothis model is OFF.If you have selected “NML” as the Surround speaker setting,1 BS NML (normal) : Average size Surround Back speakers areconnected to this model.2 BS OFF : Surround Back speaker setting mode tothis model is OFF.(VR-60RS only)If you have selected “LRG” or “NML” as the surround backspeaker setting.1 SPEAKER : Surround Back signal will be output fromSURROUND BACK speaker terminal, and SURRBACK L/ SURR BACK PRE OUT terminal asmonaural.2 PRE OUT : Surround Back signals will be output from SURRBACK L/ SURR BACK and SURR BACK R PREOUTterminals as stereo.# Press the SETUP key again to accept the setting.• The subwoofer re-mix setting indication “SW RE-MIX” scrollsacross the display.• If subwoofer is turned OFF, subwoofer re-mix setting is notvisible.Preparing for surround sound$ Use the MULTI CONTROL knob or MULTI CONTROL %/fikeys to select the appropriate Subwoofer re-mix setting.1 RMX ON : Subwoofer re-mix set mode to this model is ON.2 RMX OFF : Subwoofer re-mix set mode to this model is OFF.% Press the SETUP key to accept the setting.4Adjust the speaker volume level.From your usual listening position, adjust the volume levels. Thevolume levels from each speaker should be the same.• In step 4 and 5, indications appear only for the selected channelsof the speakers that require adjusting.1 Press the SETUP key to begin TEST TONE.• This model enters the speaker volume level adjustment mode.The selection of AUTO/MANUAL TEST TONE is done by theMULTI CONTROL knob or MULTI CONTROL %/fi keys.1 AUTO2 MANUAL2 Press the SETUP key again to select either AUTO or MANUAL.Use the MULTI CONTROL knob or MULTI CONTROL %/fi keysto adjust the volume level of the test tone output from thespeaker channel to be adjusted.For AUTO selection, the test tone is heard from the speakersin the following sequence for 2 seconds each:• If you change the volume level settings for the speakers whilelistening to music, the settings referred to on this page are alsochanged. ¶• If any of the speaker is set as OFF during SP SET UP, the TESTTONE adjustment for the speaker will be skipped.(VR-60RS only)• If you have selected “SPEAKER” as the Surround Back setting,“RB” and “LB” are not appeared but “BS” is appeared.3 Press the SETUP key.• The test tone is turned off. This model enters the mode forinputting the distance to the speakers.4 For MANUAL selection, press the SETUP key each time toselect the speaker channel.5Input the distance to the speakers.1 Select the DISTANCE from the set up displays and press theSETUP key again.2 Measure the distance from the listening position to each ofthe speakers.Jot down the distance to each of the speakers.Distance to Front Left speaker (L) : ____ feet (meters)Distance to Center speaker (C) : ____ feet (meters)Distance to Front Right speaker (R) : ____ feet (meters)Distance to Surround Right (RS) : ____ feet (meters)Distance to Surround Back Right (RB) : ____ feet (meters)Distance to Surround Back (BS) : ____ feet (meters)Distance to Surround Back Left (LB) : ____ feet (meters)Distance to Surround Left (LS) : ____ feet (meters)Distance to Subwoofer (SW) : ____ feet (meters)(VR-60RS only)• If you have selected “SPEAKER” as the Surround Back setting,“RB” and “LB” are not appeared but “BS” is appeared.Continued to next page