Kenwood VR-6070 Instruction Manual

Also see for VR-6070: Service manual Service manual Instruction manual Instruction manual Instruction manual

20 EN3 Use the ∧/∨ keys or @/# keys to select the speakers and theMULTI CONTROL knob or Multi (%/fi) keys to adjust thedistance to the front speakers.The speaker indicator to be adjusted blinks.LSL S SB SRC RSP MUTE OPTICAL 6CH INPUTCOAXIAL ANALOG 96kHzfsCINEMA EQ.ACTIVE EQ.DSP MODEDTS.MATRIXDISCRETEDOLBY DIGITALPRO LOGICSTEREOLOUDNESSNEO:6CSIIA B CLIPAUTO DETECT THXAUTORDSRTYMEMOSTEREOTUNEDSurround EXSWLFE• The allowable setting range is 1 to 30 feet (0.3 to 9.0 m),adjustable in 1 foot (0.3 m) increments.4 Repeat steps 3 to input the distance for each of the speakers.5 Press the SETUP key again to return to main setup displays.• The speakers you have selected should appear on the display.Confirm that all the speakers have been correctly selected.7 Select the display mode.1 Press the ∧/∨ key or @/# keys to select the DISP MODE.2 Press the SETUP key for the following displays:1 DISP SELECTOR : Displays the current input selector.2 DISP LISTEN : Displays the current listen mode.3 Use the MULTI CONTROL knob or Multi (%/fi) keys to selectthe display mode.SL S SB SRSP MUTE OPTICAL 6CH INPUTCOAXIAL ANALOG 96kHzfsCINEMA EQ.ACTIVE EQ.DSP MODEDTS.MATRIXDISCRETEDOLBY DIGITALPRO LOGICSTEREOLOUDNESSNEO:6CSIIA B CLIPAUTO DETECT THXAUTORDSRTYMEMOSTEREOTUNEDSurround EXLFEL C RSW4 Press the SETUP key again to accept the setting.5 Use the ∧ key or # key to select EXIT.L C RSP MUTE OPTICAL 6CH INPUTCOAXIAL ANALOG 96kHzfsCINEMA EQ.ACTIVE EQ.DSP MODEDTS.MATRIXDISCRETEDOLBY DIGITALPRO LOGICSTEREOLOUDNESSNEO:6CSIIA B CLIPAUTO DETECT THXAUTORDSRTYMEMOSTEREOTUNEDSurround EXSWLFESL S SB SR6 Press the SETUP key to exit the SET UP mode.Input level adjustment (analog sources only)If the input level of an analog source signal is too high, the CLIP indicatorwill blink to indicate the source signal. Adjust the input level.LSL S SB SRC RSP MUTE OPTICAL 6CH INPUTCOAXIAL ANALOG 96kHzfsCINEMACTIVDSP MA B CLIPAUTO DETECTSWLFECLIPCLIP1 Use the Input Selector keys to select the source of which theinput level you want to adjust.• You can store a separate input level for each input source.2 Press the SOUND and ∧/∨ keys or @/# keys repeatedly untilthe “INPUT” indication appears.3 Use the MULTI CONTROL knob or Multi (%/fi) keys to adjust theinput level.LSL S SB SRC RSP MUTE OPTICAL 6CH INPUTCOAXIAL ANALOG 96kHzfsCINEMA EQ.ACTIVE EQ.DSP MODEDTS.MATRIXDISCRETEDOLBY DIGITALPRO LOGICSTEREOLOUDNESSNEO:6CSIIA B CLIPAUTO DETECT THXAUTORDSRTYMEMOSTEREOTUNEDSurround EXSWLFE• The adjustment mode is displayed for approximately 8 seconds.• The input level may be adjusted to any one of three settings:0dB, -3dB, and -6dB. (The initial setting is 0dB.)4 Press the SOUND key again to return to the input indication.Preparing for surround sound Preparing for playbackSome preparatory steps are needed before starting playback.Turning on the receiver1 Turn on the power to the related components.2 Turn on the power to this receiver by pressing the POWERON/STANDBY key.Selecting the input modeIf you have selected a component connected to the CD/DVD, VIDEO 2,VIDEO 3 or DVD/6CH jacks, make sure that the input mode setting iscorrect for the type of audio signal to be used. 8Selecting MD/TAPESelect the source name corresponding to the component connectedto the MD/TAPE jacks. The initial factory setting is “TAPE”. Tochange the source to “MD”, follow the steps below:Hold down the MD/TAPE key for more than 2 seconds.• The source indication changes to “MD”.• To return to the original indication, repeat the above procedure.Selecting the speaker systemPress the A SPEAKERS B key to select the speaker system to beused.A ON : Sound from the speakers connected to the SPEAKERS Aterminals on the rear panel.B ON : Sound from the speakers connected to the SPEAKERS Bterminals on the rear panel. No sound will be heard fromthe subwoofer.A+B ON : Sound from both the speakers connected to theSPEAKERS A and B terminals on the rear panel.A+B OFF : No sound from the speakers. Use this setting whenlistening with headphones for stereo sound in all playbackmodes. The display segments are different depending onthe type of input signal.The indicator for the speakersyou want to use should be lit.• Selecting “6CH INPUT” by pressing the INPUT MODE key, whereby“DVD/6CH” is the input source will cause SPEAKERS A to be selectedautomatically.Normal playbackINPUT MODEMD/TAPEA SPEAKERS BPOWERON/STANDBYLSL S SB SRC RSP MUTE OPTICAL 6CH INPUTCOAXIAL ANALOG 96kHzfsCINACTDSA B CLIPAUTO DETECTSWLFEIndication in feet Indication in meters