Manuals database logo
manualsdatabase
Your AI-powered manual search engine

La Marche DCPS Installation And Operation Manual

Also see for DCPS: Installation and operation manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Page 32 preview
Page 33 preview
Page 34 preview
Page 35 preview
Page 36 preview
Page 37 preview
Page 38 preview
Page 39 preview
Page 40 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. Table Of Contents
  4. Overview
  5. Configurations
  6. DCR – Rectifier
  7. Figure 6 – DCR Panel
  8. DCSC – System Controller
  9. Figure 9 – RS485/RS232 Port and FE Port Pinout
  10. DCU – User Interface Module
  11. Table 8 – DCU Ports
  12. Figure 11 – DCU Pin Numbers
  13. Installation
  14. Unpacking and Acceptance
  15. Installing Subrack into a 23-Inch Rack
  16. Installing Components
  17. Figure 18 – Removing the Top Cover
  18. Installing a Ground Cable
  19. Installing Communication Cables
  20. Reinstalling AC Dual-Live Wire Input Power Cables
  21. Installing AC Input Power Cable
  22. Figure 28 – Installing Power Cables for four AC dual-live Wire Inputs
  23. Figure 30 – Installing Power Cables for two AC dual-live Wire Inputs
  24. Verifying the Installation
  25. Commissioning
  26. Optional) Setting the Hibernation Parameter
  27. Figure 32 – Login
  28. Connecting the Battery Supply
  29. Maintenance
  30. A Technical Specifications
  31. B Electrical Conceptual Diagram
  32. C Associations Between Alarms and Dry Contacts on the DCU
  33. D Acronyms and Abbreviations
  34. E Smoke Sensor Accessory Safety Notification
  35. Manufacturer's Warranty
  36. Document Control and Revision History
La Marche DCPS Installation And Operation Manual Manual pdf 22 page image
163.6 Installing Communication Cables If the power system connects to power and environmental monitoring equipment, connect thecommunications cables to the RS485/RS232 port on the DCSC. If the power system requires remote management over the WebUI or a third-party SNMP device,connect the communications cables to the FE port.3.7 Installing DC Output Power CablesPrerequisitesDANGER:Switch off all circuit breakers before installing power cables.ProcedureStep 1 Route DC output power cables through a cable hole on the rear of the subrack.Step 2 Connect the negative DC output power cable to the corresponding DC output terminal based onthe actual load power.Step 3 Connect the positive DC output power cable to the corresponding screw on the RTN+ busbar.Figure 23 – Installing DC Power Output Cables(1) Load3.8 Installing Battery CablesPrerequisitesCAUTION:Switch off all circuit breakers before installing power cables.ProcedureStep 1 Route battery cables from a cable hole on the rear of the subrack.Step 2 Connect the negative battery cable to the battery wiring terminal.Step 3 Connect the positive battery cable to the RTN+ busbar.
/ 40
Related manuals for La Marche DCPS
La Marche DCPS Installation And Operation Manual first page preview
La Marche DCPS Installation And Operation Manual
La Marche TPSD Installation And Operation Manual first page preview
La Marche TPSD Installation And Operation Manual
La Marche P24B-18-12V Quick Start Manual first page preview
La Marche P24B-18-12V Quick Start Manual
This manual is suitable for:
DCPS
Manuals database logo
manualsdatabase
Your AI-powered manual search engine